MIC/AUDIO2

 

Items/

Adjustable

Remarks

Data Saved

Range

 

FRONT MIC

ON

Select the phantom power supply for the

POWER

OFF

front microphone.

–

C

U

F

–

 

 

REAR MIC

ON

Select the phantom power supply for the

POWER

OFF

rear microphone.

 

 

 

 

 

 

When “OFF” is selected, no phantom

 

 

 

 

 

 

power is supplied even if the LINE/MIC/

 

 

 

 

 

 

+48V selector switch is set to [+48V].

–

C

U

F

–

 

 

MONITOR

STEREO

When the MONITOR select switch is set

SELECT

MIX

to [ST] (stereo), select the signal format

 

 

 

 

 

 

for the monitor output.

–

C

U

F

–

 

 

FRONT MIC

–40dB

Select the front microphone input level.

LEVEL

–50dB

 

–

C

U

F

–

 

 

REAR MIC CH1

–50dB

Select the rear microphone input level.

LVL

–60dB

 

–

C

U

F

–

 

 

REAR MIC CH2

–50dB

Select the rear microphone input level.

LVL

–60dB

 

–

C

U

F

–

 

 

REAR LINE IN

–3dB

Select the rear line input level.

LVL

0dB

 

 

 

 

 

 

+4dB

 

–

C

U

F

–

 

 

AUDIO OUT LVL

–3dB

Select the audio output level.

 

 

 

 

 

0dB

 

 

 

 

 

 

+4dB

 

–

C

U

F

–

 

 

HEADROOM

18dB

Set the headroom (standard level).

 

 

 

 

 

20dB

 

–

C

U

F

–

 

 

WIRELESS

ON

Select whether or not to enable the

WARN

OFF

alarm to trigger for poor wireless receiver

 

 

 

 

 

 

reception.

–

C

U

F

–

 

 

WIRELESS

SINGLE

Select the type of wireless receiver.

TYPE

DUAL

SINGLE:

 

 

 

 

 

 

Select a single channel wireless

 

 

 

 

 

 

receiver.

 

 

 

 

 

 

DUAL: Select a 2-channel wireless

 

 

 

 

 

 

receiver.

–

C

U

F

–

 

 

TC/UB

 

Items/

Adjustable

 

Remarks

 

 

Data Saved

Range

 

 

 

 

 

 

 

TC MODE

DF

Set the time code mode.

 

 

 

 

 

 

 

NDF

DF:

Drop frame.

 

 

 

 

 

 

 

 

NDF:

Non drop frame.

 

 

 

 

 

 

 

 

Note

 

 

 

 

 

 

 

 

 

When the unit operates at 50 Hz or in

 

 

 

 

 

 

 

 

24P or 24PA mode, the non-drop frame

 

 

 

 

 

 

 

 

is always used.

 

 

–

C

U

F

–

 

 

 

 

 

UB MODE

USER

Select the user bits mode.

 

 

 

 

 

 

 

TIME

USER: Select UB value set in the LCD

 

 

 

 

 

 

 

DATE

 

section.

 

 

 

 

 

 

 

EXT

TIME:

 

 

 

 

 

 

 

Select local time (hours,

 

 

 

 

 

 

 

TCG

 

 

 

 

 

 

 

FRM RATE

 

minutes, seconds).

 

 

 

 

 

 

 

REGEN

DATE: Select local date and time (2 last

 

 

 

 

 

 

 

 

EXT:

digits of year, month, date, time).

 

 

 

 

 

 

 

 

The user bits input to the TC IN

 

 

 

 

 

 

 

 

 

connector are recorded.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If reading fails, USER value is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TCG:

retained.

 

Menu

 

 

 

 

 

 

TCG value enters UB.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FRM RATE:

 

 

 

 

 

 

 

 

 

Select the shooting information

 

 

 

 

 

 

 

 

 

(e.g. frame rate) for the camera.

 

 

 

 

 

 

 

 

 

For more information, see

 

 

 

 

 

 

 

 

 

[Frame rate information

 

 

 

 

 

 

 

 

 

recorded in user bits] (page 63).

 

 

 

 

 

 

 

 

 

When clips recorded in native

 

 

 

 

 

 

 

 

 

mode are played back, the frame

 

 

 

 

 

 

 

 

 

rate information recorded in

 

 

 

 

 

 

 

 

 

users bits in the VAUX area is

 

 

 

 

 

 

 

 

 

output.

 

 

 

 

 

 

 

 

REGEN: Read out value stored in the

 

 

 

 

 

 

 

 

 

card and record value

 

 

 

 

 

 

 

 

Note

continuously.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When the unit is in 720P mode, “FRM

 

 

 

 

 

 

 

 

RATE” is always selected.

 

 

–

C

U

F

–

 

 

 

 

 

Menu: Menu Description Tables 193