CA28T103 Connection Procedure | Panasonic AW-E560 manual

■CA28T103 CONNECTION PROCEDURE

•Connecting Receiver and Control Cable CA28T103

•The control cable CA28T103 is provided with a circuit board and spacers.

•Assemble the circuit board and spacer with the receiver WV-RC100 (WV-RC150), and connect the control cable to that circuit board.

(1)Remove the two screws on the connector board shown from inside the receiver.

(2)Fit the two spacers on the connector board and fasten the circuit board with the screws removed in Step (1).

Spacer

Screws

Circuit board, an accessory to the cable

-23-

Image 25

Panasonic AW-E560 manual CA28T103 Connection Procedure

Contents

AW-E560 Lightning flash with arrowhead sym Contents Preface FeaturesAGC Special Notes on Operation Donts PrecautionsPage Top View Bottom View Front View Major Operating Controls and Their Functions Item Switch ITEM/AWC SwitchUp Switch UP/ABC Down Switch DOWN/BAR Iris Connector Iris Video Output Connector Video OUTZoom/Focus Connector ZOOM/FOCUS Power Indicator Remote Connector RemoteDC Input Connector EXT DC Control Connector Control Video/RGB Output Connector VIDEO/RGB Lens Mounting 15. G/L Signal 75-ohm ON/OFF Switch 75Ω ON/OFF Iris Gain Control in a Lens Flange Back Adjustment Connections Connection of Device with a Composite Input Connector Connector pin layout How to assemble the power cable Wires Connection of a Remote Controller RCU and a Studio Cable Multiplex adaptor WV-PS550 Connection of a Remote Control BOX RCB Connection with Multiple Cameras Connection of Computer Interface Adaptor PC Mode System CA20TBNC Connection Procedures for Cable KIT WV-CA28T10 DC12V CA28T103 Connection Procedure Page Color temperature and adjustment of white balance Adjustment Adjustment with the RCU RCB Manual White Balance Setting Automatic Tracking White Balance Setting ATW Black Balance Adjustment Adjustment by Camera Reset to 3200K or 5600K White BalanceAdjustment with RCU or RCB Total Pedestal Level Adjustment Horizontal Phase Control GEN-LOCK Adjustment Phase Coarse Fine RET END Color Phase Adjustment Operation Mode Setting Operation Mode SettingSettings CURRMODE1/SCENE1 SCENE2 SCENE3 User a User B Setup Memory Menu Item SettingSetup State Setup Data Screen Camera Alone Iris Control Setting Iris MANU, Auto Scene 2 Scene How to Read Screens Initial SET Menu SettingHow to Set Initial Set Memory Initial Set Screen Initial Set State RCU RCB Camera Alone Total Pedestal Adjustment T PED Red gain adjustment R Gain Blue gain adjustment B Gain2Painting Setting Painting ON/OFF 3AUTO IRIS/AGC/ELC Level Adjustment Level Frame Auto Iris ADJ ON/ADJ OFFOFF @6Output Signal Setting 2 Output SEL2 Y/C, Composite @5Output Signal Setting@8Camera ID on/off setting Camera ID ON/OFF @9Time Date on/off setting Time Date ON/OFF SETUP/INITIAL Set Memory Reset User Setting User Setup Menu SettingScene File Memory User Set Screens Camera Alone Camera with RCU RCB #2White Clip Level Setting White Clip 95% to 110% #1Knee Compensation Level Setting Knee Point 88% to 98%#4Detail Band Level Setting DTL Band 1 to #5Noise Suppress Compensation Level Setting Noise SUP 0 to Gammanor YES UP SW No Down SW NOW Reset User a Memory User Set Memory Reset Camera Installation Camera ID Setting Camera ID SettingCamera ID UP SW ← → Down SW Item SW Camera ID Display Position Camera ID Display Position SettingCamera ID Position Set Screen Time/Date Setting TIME/DATE SettingTime/Date Set Screen Camera Alone Time/Date Display Position Set Screen Time/Date Display Position SettingTime/Date Display Position Iris Auto Manu Setup Menu Shutter OFF ELC White BAL Range of SETUP/INITIAL SET and Their Initial ValuesPurpose Indoor AGC High AGC LOW Scene User a User B Range of Scene FILE/USER SET and Their Initial ValuesGamma NOR Gamma SHT Knee Point White Clip Flare R SCENE/USER File and Their Initial Value MODE2 SCENE/USER File Initial Value MODE3 SCENE/USER File and Their Initial Value MODE4 Ntsc SpecificationsVBS, BB, HD, VD AUTO, ELC Optional Accessories Standard AccessoriesWV-RC700A WV-CB700A N1097-0 7J1A095A