ªCondensation
If the Condensation Indication flashes after the Movie Camera is turned on, condensation has formed inside the Movie Camera. In this case, the Movie Camera power is turned off automatically after about 1 minute.
Follow the steps below:
1Take out the Cassette.
≥None of the other functions operate. Depending on the amount of condensation, removing the Cassette may even become difficult. If this happens, wait for
2 to 3 hours before taking the Cassette out.
2Open the Cassette Compartment Cover and wait for 2 to 3 hours.
≥The number of hours to wait depends on the amount of condensation and ambient temperature.
32 to 3 hours later, turn on the Movie Camera power and check to see if the Condensation Indication is displayed.
≥Even if the Condensation Indication is not displayed,
as a precaution, please wait for another hour before using the Movie Camera.
Watch for Condensation even before the Condensation Indication is displayed.
≥Because condensation takes place gradually, the Condensation Indication may not be displayed during the first 10 to 15 minutes of condensation formation inside the Movie Camera.
≥In extremely cold places, condensation may freeze and form frost. In this case, the frost melts first, thus forming condensation, and then it takes another 2 to 3 hours to eliminate the condensation.
When the Lens is Fogged:
Set the [OFF/ON/MODE] Switch to [OFF] and leave the Movie Camera in this condition for about 1 hour. When the lens temperature becomes close to the ambient temperature, the fog disappears naturally.
ªVideo Head Clogging and Care
If the heads (the parts that make contact with tape) are dirty,
Causes of Dirty Heads
≥Large quantity of dust in the air
≥Long operating hours
Using
1Insert the Head Cleaner into the Movie Camera in the same manner as a Video Cassette.
2Press the [1] Button, and approximately 20 seconds later, press the [∫] Button. (Do not rewind the tape.)
3Take out the Head Cleaner. Insert a Video Cassette and start recording. Then, play the tape back to check the recorded image.
4If the image is not still clear, repeat Steps 1 to 3. (Do not use the Head Cleaner for 3 times or
more consecutively.)
Notes:
≥Do not rewind every time you use the Head Cleaner. Rewind only when the tape reaches the end, and then use it again from the beginning in the same manner as before.
≥If the heads become dirty soon after cleaning, the tape may be damaged. In this case, immediately stop using that Cassette.
≥Do not clean the heads excessively. (Excessive cleaning may cause excessive wear of the heads. If the heads are worn, images cannot be played back even after the heads are cleaned.)
≥If the dirty heads cannot be cleaned with the Head Cleaner, the Movie Camera needs to be cleaned at a service centre.
Please consult a dealer.
≥Video Head Cleaners can be purchased from service centres.
≥Head cleaning due to dirty heads is not considered a malfunction of the product. It is not covered by the warranty.
Periodical Check-up
To maintain the highest image quality, we recommend replacement of worn parts, such as heads, etc., after approximately 1000 hours of use. (This, however, depends on operating conditions, such as temperature, humidity, dust, etc.)
ªOptimal Use of the Battery
Battery Characteristics
This Battery is a rechargeable lithium ion battery. Its ability to generate power is based upon the chemical reaction that takes place inside it. This reaction is susceptible to the surrounding temperature and humidity, and, if the temperature is too high or too low, the operating time of the Battery becomes shorter. If the Battery is used in an extremely cold environment, the Battery may operate only for about 5 minutes. If the Battery becomes extremely hot, a protective function may operate, and the Battery may become unusable for a while.
Be Sure to Detach the Battery after Use
Be sure to detach the Battery from the Movie Camera. (If it is left attached to the Movie Camera, a minute amount of current is consumed even when the Movie Camera power is off.) If the Battery is left attached to the Movie Camera for a long time, over discharge takes place. The Battery may become unusable after it is charged.
Disposing of an Unusable Battery ≥The Battery has a limited life.
≥Do not throw the Battery into fire because it may cause an explosion.
Always Keep the Terminals of the Battery Clean
Prevent the terminals from getting clogged with dirt, dust, or other substances.
If you drop the Battery accidentally, check to see if the Battery body and terminals are deformed.
Attaching a deformed Battery to the Movie Camera or AC Adaptor may damage the Movie Camera or AC Adaptor.
53
