Specifications, PAL-N / Secam | Panasonic PT-L712NTE guide

Specifications

Identical specifications appear in the separate PT-L712E Operating Instructions, but the following should be referred to for details on PT-L712NTE specifications.

Power supply:		100 V - 240 V ~, 50 Hz/60 Hz
Power consumption:		240 W Approx. 5 W - 10 W when in
		standby mode (when fan is stopped)
Amps:		2.8 A - 1.0 A
LCD panel:
Panel size (diagonal):		0.9 type (22.86 mm)
Aspect ratio:		4:3 (16:9 compatible)
Micro lens array:		Available
Display method:		3 transparent LCD panels (RGB)
Drive method:		Active matrix method
Pixels:		786 432 (1024 x 768) x 3 panels
Lens:		Manual zoom (1 - 1.3) / focus lens
		F 1.8 - 2.1, f 28.7 mm - 36.0 mm
Lamp:		UHM lamp (165 W)
Luminosity:		1600 lm/ANSI
Scanning frequency:		(for RGB signals)
		Internal data (point scanning) method
	Horizontal scanning frequency			24 kHz - 97 kHz
	Vertical scanning frequency			50 Hz - 120 Hz
	Dot clock frequency			135 MHz or less
YPBPR signals:		NTSC (480i), 480p, PAL (625i), 720p,
		HDTV (1080i/1035i)
Colour system:		6 (NTSC / NTSC 4.43 / PAL / PAL-M /
		PAL-N / SECAM)
Projection size:		762 mm - 7620 mm (30" - 300")
Throw distance:		1.1 m - 11.7 m (3'8" - 38'4")
Optical axis shift:		9:1 (fixed)
Screen aspect ratio:		4:3
Installation:		Front/Rear/Ceiling/Desk (Menu
		selection method)
Speakers:		2.8 cm round x 2
Max. useable volume output:		2 W (1 W + 1 W) (stereo)
Connection terminals:
RGB/YPBPR IN:		Dual-line D-SUB HD 15-pin (female)
During YPBPR input:
	Y:	1.0 V [p-p] (including sync signal),
	PB,PR:	75 Ω
		0.7 V [p-p], 75 Ω
		-64-

Image 64

Panasonic PT-L712NTE manual Specifications, PAL-N / Secam

Contents

Operating Instructions LCD Projector Commercial Use Contents Dear Panasonic Customer Safety PrecautionsDo not insert any foreign objects into the card slot Radio frequencies used by the wireless card Do not use the cards near other sources of radio emissions Available channels Etsi Check accessories Wireless card slotWireless card Names of each part Wireless image transfer system for the projector System diagram Transferable images Main functions of the application software Software Functions Explanation of terms IP AddressSubnet Mask Gateway Ad Hoc Mode Infrastructure ModeAccess Point Channel Jpeg PowerPoint Exif Wireless function preparation Firstly, when using the wireless functionSetting procedure Setting example ComputerProjectorComputer LAN Page Installing and removing the wireless card Inserting the wireless card# Turn off the power supply for the projector Close the slot cover $ Open the slot cover Press the eject switch Removing the wireless cardPush in the eject switch and then remove the wireless card On-screen menus List of menu screens Projector LAN settings LAN Setup Lock Setup $ Mode Channel Ssid Subnet Mask KEY Installing and removing the computer’s wireless card Setting up the computer wireless cardInstalling the wireless card Removing the wireless card Installing the driverFor Windows Click OK without changing any of the detailed settings Click Finish Click Yes. The computer will then re-start Checking the protocol Click YesPage Click OK + Click Yes. The computer will then Re-start Page Installing the Configuration Utility Click Close Using the Wireless Manager Wireless Manager capabilitiesStarting and closing the Wireless Manager Displaying the Configuration Utility Computer network settings Make the following settings # Select Setting $ Setting NameCreate Delete Wireless LAN Mode Checking communication with the projector Basic image transmission examples Example 2 Projecting already-existing images Capturing and transmitting computer screen images Before transmitting imagesFunctions of the Capture window Selecting the capturing method Close button Area capture Full Screen capture$ Right-click the icon on the taskbar, and select Capture Active Window capture Click Capture Start Select the window to be captured. Note Setting the capturing conditions Transmitting existing images Functions in the Image List window Basic operations Using Auto Play to play images in a specified order Image List status settings# Number of Loops $ Interval Other useful Wireless Manager functions Shortcut Key Assignment Encryption settings Using Jpeg Convertor What Jpeg Convertor can do Starting Jpeg Convertor Main screen functions + Picture quality slider Save to SD Memory Card buttonMinimize button Maximize button Quality Importing files using drag-and-drop Images which cannot be imported Checking, sorting and deleting images Checking imagesSorting images Double click on the image you wish to check Conversion settings for saving images Deleting images Saving to other folders Save as different size check boxConverted size list box Picture quality slider DCF standard Limits on directory namesFile names File format Using the Serial connector Before asking for serviceSymptom Check the following Message List Symptom Check the following Symptom Check the following Specifications PAL-N / Secam Sync Wireless card Options Dimensions Trademark Information Made in Japan S0801-2081C