Manuals / Panduit / Computer Equipment / Printer

Panduit TDP42H, TDP43H, TDP46H manual Panduit TDP4*H

Models: TDP46H TDP43H TDP42H

1 84

Download 84 pages 23.38 Kb

Page 43

TRUETYPE

FONTCOPY

COMPLETED

CARD COPY/FORMAT XXXXXXX ERROR

CARD->MEMORYCOPY

SATO FONT

Y/N

COPY START

YES NO

SATO FONT COPY

COPYING

SATO FONT COPY

COMPLETED

CARD COPY/FORMAT XXXXXXX ERROR

MEMORY->CARDCOPY ALL <0MB> Y/N

COPY START

YES NO

PANDUIT TDP4*H

Section 3: Configuration

4.Once the copy process is completed, press the FEED key to step the display.

5.If an error is encountered in the copy process, one of the following messages will be displayed on the second line:

R/W Error	Indicates a Read/Write error occurred
No Card Error	Indicates no card was recognized

Mem Full Error Indicates that there is insufficient memory available.

This selection allows you to copy SATO fonts from the PCMCIA Memory card installed in the Memory Card slot on the rear of the printer to the optional Flash ROM.

1.Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will enter the Card Copy mode. If No is selected, the display will advance to the Card to Memory Copy All mode.

2.Confirm your selection by stepping the cursor to the Yes selection. If you select No, the display will return to the previous selection.

3.Press the FEED key to accept the selection. If Yes was selected the copy process will start

4.Once the copy process is completed, press the FEED key to step the display.

5.If an error is encountered in the copy process, one of the following messages will be displayed on the second line:

R/W Error	Indicates a Read/Write error occurred
No Card Error	Indicates no card was recognized

Mem Full Error Indicates that there is insufficient memory available.

This selection allows you to copy the entire contents from the PCMCIA Memory card installed in the Memory Card slot on the rear of the printer to the optional internal Expanded Memory.

1.Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will enter the Card Copy mode. If No is selected, the display will advance to the Card to Memory Copy All mode.

2.Confirm your selection by stepping the cursor to the Yes selection. If you select No, the display will return to the previous selection.

GMTDPH-MAN

Page 3-17

Image 43

Panduit TDP42H, TDP43H, TDP46H manual Panduit TDP4*H

Contents

TDP42H, TDP43H, TDP46H Panduit Corp Troubleshooting InstallationConfiguration Cleaning and MaintenanceOptional Accessories Interface SpecificationsC T I O N Pr i n t e r O v e r v i e w Introduction Specification TDP42H TDP43H TDP46H Print General Printer SpecificationsSpecification Character Fonts Specification TDP42H TDP43H TDP46H Matrix FontsBar Codes SymbologiesPhysical PowerAccessories and Options GMTDPH-MAN Panduit TDP4*H C T I O N Installation Introduction Unpacking and Parts Identification Setting Up the Printer GMTDPH-MAN Panduit TDP4*H Loading Labels and Tags GMTDPH-MAN Panduit TDP4*H Panduit TDP4*H GMTDPH-MAN Loading the Ribbon Panduit TDP4*H GMTDPH-MAN LCD Display Panel Operator PanelOn Line EXT Rear PanelLabel Indexing Sensor SensorsGMTDPH-MAN Panduit TDP4*H Setting DSW1 DIP Switch PanelsRS232 TRANSMIT/RECEIVE Setting SettingDSW2 OFF Printer SET UPDSW2-2 Off Cutter Not Used Setting DSW3DSW3 OFF DSW3 OFFDSW3-6 DSW3-7 Default Completed Default SettingsSwitch Selections Software Default SettingsPitch Potentiometer AdjustmentsBackfeed Offset Print DisplayNormal Mode LCD Panel Printer ConfigurationInitializing Online QTY000000 Print Darkness OfflinePrint Speed Pitch Offset +00mm Cancel Print JOB YES no Completed Advanced ModeInitializing Advanced Mode Zero Slash YES no Auto Online SET Calendar YES no Print OffsetIgnore CR/LF YES no CalendarCharacter Pitch Prop Fixed Advanced Mode Card ModeCopy Start YES no Panduit TDP4*H CARD-MEMORY Copy Copying CARD-MEMORY Copy Copying Initializing Advanced Mode Service Mode GAPX.XXV INPUTX.XV Service ModeGAPX.XXV INPUTX.XV EYEX.XXV INPUTX.XV Auto Online Feed YES no Feed on Error EXT PIN 9 Select MODE1 MODE2 Euro Code Reprint W/FEED YES no FORWARD/BACKFEED Distance DefaultService Mode ACK SignalTest Print Mode Counters ModeInitializing Initializing Default Setting YES no Default Setting ModeTest Print Size 10 CM Press Feed KEY to Stop Printing Initializing User Download Press the Line KEY Default Setting CompletedClear NON-STANDARD Protocol Download User Defined Protocol CodesUser Download Waiting HEX Dump ModeInitializing Online Print Darkness Adjusting the Print QualityPrint Speed Cleaning the Print Head, Platen and RollersCleaning the Platen and Rollers Cleaning the Label Edge SensorsReplacing the Print Head Do not remove the two outside screws painted red Cleaning and Maintenance Using the IEEE1284 Parallel Interface Initial ChecklistC T I O N Tr o u b l e s h o o t i n g Introduction Using the RS232C Serial Interface Using the Lan Ethernet Interface Using the Universal Serial Bus USB InterfacePrinter does not Come UP Ready Checking the Network Connection and Cabling Intermittent ProblemsLED LCD Message Audible Beep Error Condition Possible Causes GMTDPH-MAN Panduit TDP4*H Interface Types C T I O N T e r f a c e Specification s IntroductionSingle JOB Buffer Receive BufferMulti JOB Buffer IEEE1284 Parallel Interface Data Streams Electrical SpecificationsPIN Signal Direction IEEE1284 Parallel Interface Pin AssignmentsRS232 Serial Interface General SpecificationsPIN RS232C Interface SignalsSignal Definition PIN AssignmentsREADY/BUSY Flow Control Cable RequirementsON/X-OFF Flow Control Local Area Network LAN Optional Interface Universal Serial Bus USB InterfaceBi-Directional Communications Print JOB Cancel canENQUIRE/ACK/NAK Enquire ENQPrint Start DC1 Print Stop DLEPcmcia Memory Cards InstallationError Handling C T I O N T i o n a l Ac c e s s o r i e s IntroductionPlug-In Interface Modules Error Description Indication RemedyCutter Operator SetupGeneral Operation Label Dispense Option Removing and Unwinding the Roll Label RewinderReal Time Clock