Manuals / Panduit / Computer Equipment / Printer

Panduit TDP46H, TDP43H, TDP42H manual CARD-MEMORY Copy Copying

Models: TDP46H TDP43H TDP42H

1 84

Download 84 pages 23.38 Kb

Page 44

Section 3: Configuration

CARD->MEMORY

COPY COPYING

CARD->MEMORYCOPY COMPLETED

CARD COPY/FORMAT XXXXXXX ERROR

MEMORY->CARDCOPY ALL <0MB> Y/N

COPY START

YES NO

MEMORY->CARDCOPY COPYING

MEMORY->CARDCOPY COMPLETED

CARD COPY/FORMAT XXXXXXX ERROR

CARD->MEMORYCOPY

PROGRAM Y/N

COPY START

YES NO

Page 3-18

3.Press the FEED key to accept the selection. If Yes was selected the copy process will start.

4.Once the copy process is completed, press the FEED key to step the display.

5.If an error is encountered in the copy process, one of the following messages will be displayed on the second line:

R/W Error	Indicates a Read/Write error occurred
No Card Error	Indicates no card was recognized

Mem Full Error Indicates that there is insufficient memory available.

This selection allows you to copy the entire contents of the optional Expanded Memory to the PCMCIA Memory card installed in the Memory Card slot on the rear of the printer.

1.Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will enter the Card Copy mode. If No is selected, the display will advance to the Card to Memory Copy All mode.

2.Confirm your selection by stepping the cursor to the Yes selection. If you select No, the display will return to the previous selection.

3.Press the FEED key to accept the selection. If Yes was selected the copy process will start

4.Once the copy process is completed, press the FEED key to step the display.

5.If an error is encountered in the copy process, one of the following messages will be displayed on the second line:

R/W Error	Indicates a Read/Write error occurred
No Card Error	Indicates no card was recognized

Mem Full Error Indicates that there is insufficient memory available.

This selection allows the user to copy printer firmware from the PCMCIA Memory Card to the printer.

1.Use the LINE key to step the cursor to desired setting. If Yes is selected, the printer will enter the Card Copy mode. If No is selected, the display will advance to the mode display.

2.Confirm your selection by stepping the cursor to the Yes selection. If you select No, the display will return to the previous selection.

GMTDPH-MAN

PANDUIT TDP4*H

Image 44

Panduit TDP46H, TDP43H, TDP42H manual CARD-MEMORY Copy Copying

Contents

TDP42H, TDP43H, TDP46H Panduit Corp Installation ConfigurationCleaning and Maintenance TroubleshootingInterface Specifications Optional AccessoriesC T I O N Pr i n t e r O v e r v i e w Introduction General Printer Specifications Specification TDP42H TDP43H TDP46H PrintSpecification Specification TDP42H TDP43H TDP46H Matrix Fonts Character FontsSymbologies Bar CodesPower PhysicalAccessories and Options GMTDPH-MAN Panduit TDP4*H C T I O N Installation Introduction Unpacking and Parts Identification Setting Up the Printer GMTDPH-MAN Panduit TDP4*H Loading Labels and Tags GMTDPH-MAN Panduit TDP4*H Panduit TDP4*H GMTDPH-MAN Loading the Ribbon Panduit TDP4*H GMTDPH-MAN Operator Panel LCD Display PanelOn Line Rear Panel EXTSensors Label Indexing SensorGMTDPH-MAN Panduit TDP4*H DIP Switch Panels RS232 TRANSMIT/RECEIVE SettingSetting Setting DSW1Printer SET UP DSW2 OFFDSW2-2 Setting DSW3 Off Cutter Not UsedDSW3 OFF DSW3 OFFDSW3-6 DSW3-7 Default Settings Switch SelectionsSoftware Default Settings Default CompletedBackfeed Offset Potentiometer AdjustmentsPitch Display PrintInitializing Online QTY000000 LCD Panel Printer ConfigurationNormal Mode Print Speed OfflinePrint Darkness Pitch Offset +00mm Initializing Advanced Mode Zero Slash YES no Auto Online Advanced ModeCancel Print JOB YES no Completed Print Offset SET Calendar YES noCalendar Ignore CR/LF YES noCopy Start YES no Card ModeCharacter Pitch Prop Fixed Advanced Mode Panduit TDP4*H CARD-MEMORY Copy Copying CARD-MEMORY Copy Copying Service Mode Initializing Advanced Mode Service Mode GAPX.XXV INPUTX.XVGAPX.XXV INPUTX.XV EYEX.XXV INPUTX.XV Auto Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default EXT PIN 9 Select MODE1 MODE2 Euro CodeACK Signal Service ModeInitializing Counters ModeTest Print Mode Test Print Size 10 CM Press Feed KEY to Stop Printing Default Setting ModeInitializing Default Setting YES no Default Setting Completed Clear NON-STANDARD ProtocolDownload User Defined Protocol Codes Initializing User Download Press the Line KEYInitializing Online HEX Dump ModeUser Download Waiting Adjusting the Print Quality Print DarknessCleaning the Print Head, Platen and Rollers Print SpeedCleaning the Label Edge Sensors Cleaning the Platen and RollersReplacing the Print Head Do not remove the two outside screws painted red Cleaning and Maintenance C T I O N Tr o u b l e s h o o t i n g Introduction Initial ChecklistUsing the IEEE1284 Parallel Interface Using the RS232C Serial Interface Printer does not Come UP Ready Using the Universal Serial Bus USB InterfaceUsing the Lan Ethernet Interface Intermittent Problems Checking the Network Connection and CablingLED LCD Message Audible Beep Error Condition Possible Causes GMTDPH-MAN Panduit TDP4*H C T I O N T e r f a c e Specification s Introduction Interface TypesMulti JOB Buffer Receive BufferSingle JOB Buffer IEEE1284 Parallel Interface Electrical Specifications PIN Signal DirectionIEEE1284 Parallel Interface Pin Assignments Data StreamsGeneral Specifications RS232 Serial InterfaceRS232C Interface Signals Signal DefinitionPIN Assignments PINON/X-OFF Flow Control Cable RequirementsREADY/BUSY Flow Control Bi-Directional Communications Universal Serial Bus USB InterfaceLocal Area Network LAN Optional Interface Cancel can ENQUIRE/ACK/NAKEnquire ENQ Print JOBPrint Stop DLE Print Start DC1Installation Error HandlingC T I O N T i o n a l Ac c e s s o r i e s Introduction Pcmcia Memory CardsError Description Indication Remedy Plug-In Interface ModulesGeneral Operation Operator SetupCutter Label Dispense Option Label Rewinder Removing and Unwinding the RollReal Time Clock