Manuals / Panduit / Computer Equipment / Printer

Panduit TDP42H, TDP43H, TDP46H manual Print Stop DLE, Print Start DC1

Models: TDP46H TDP43H TDP42H

1 84

Download 84 pages 23.38 Kb

Page 76

Section 6: Interface Specifications

PRINT STOP (DLE)

If a DLE (10 hexadecimal) is received by the printer, the print process is stopped and an ACK (06 hexadecimal) is returned if there are no errors and a NAK (16 hexadecimal) if a printer error exists.

PRINT START (DC1)

If the printer has been stopped by receipt of a DLE (10 hexadecimal) command, it can be restarted by sending a DC1 (hexadecimal 11) command. Upon receipt of this command an ACK (06 hexadecimal) is returned if there are no errors and a NAK (16 hexadecimal) if a printer error exists.

Note: To provide compatibility with older PANDUIT ® printers, the RS232C interface can be configured to use an earlier Bi-Com 3 ENQ/ACK/NAK protocol selected via DSW2-8 and DSW1-7/8 (on the RS232 Interface module).The earlier protocol did not have provisions for the Job Name and did not respond to the DLE or DCI commands. Also, there are additional Response Codes in the Status Byte Definition. It is recommended that you use the current protocol rather than the earlier version unless it is necessary for compatibility with existing software.

Page 6-10

GMTDPH-MAN

PANDUIT TDP4*H

Image 76

Panduit TDP42H, TDP43H, TDP46H manual Print Stop DLE, Print Start DC1

Contents

TDP42H, TDP43H, TDP46H Panduit Corp Installation ConfigurationCleaning and Maintenance TroubleshootingInterface Specifications Optional AccessoriesC T I O N Pr i n t e r O v e r v i e w Introduction General Printer Specifications Specification TDP42H TDP43H TDP46H PrintSpecification Specification TDP42H TDP43H TDP46H Matrix Fonts Character FontsSymbologies Bar CodesPower PhysicalAccessories and Options GMTDPH-MAN Panduit TDP4*H C T I O N Installation Introduction Unpacking and Parts Identification Setting Up the Printer GMTDPH-MAN Panduit TDP4*H Loading Labels and Tags GMTDPH-MAN Panduit TDP4*H Panduit TDP4*H GMTDPH-MAN Loading the Ribbon Panduit TDP4*H GMTDPH-MAN Operator Panel LCD Display PanelOn Line Rear Panel EXTSensors Label Indexing SensorGMTDPH-MAN Panduit TDP4*H DIP Switch Panels RS232 TRANSMIT/RECEIVE SettingSetting Setting DSW1Printer SET UP DSW2 OFFDSW2-2 Setting DSW3 Off Cutter Not UsedDSW3 OFF DSW3 OFFDSW3-6 DSW3-7 Default Settings Switch SelectionsSoftware Default Settings Default CompletedPitch Potentiometer AdjustmentsBackfeed Offset Display PrintNormal Mode LCD Panel Printer ConfigurationInitializing Online QTY000000 Print Darkness OfflinePrint Speed Pitch Offset +00mm Cancel Print JOB YES no Completed Advanced ModeInitializing Advanced Mode Zero Slash YES no Auto Online Print Offset SET Calendar YES noCalendar Ignore CR/LF YES noCharacter Pitch Prop Fixed Advanced Mode Card ModeCopy Start YES no Panduit TDP4*H CARD-MEMORY Copy Copying CARD-MEMORY Copy Copying Service Mode Initializing Advanced Mode Service Mode GAPX.XXV INPUTX.XVGAPX.XXV INPUTX.XV EYEX.XXV INPUTX.XV Auto Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default EXT PIN 9 Select MODE1 MODE2 Euro CodeACK Signal Service ModeTest Print Mode Counters ModeInitializing Initializing Default Setting YES no Default Setting ModeTest Print Size 10 CM Press Feed KEY to Stop Printing Default Setting Completed Clear NON-STANDARD ProtocolDownload User Defined Protocol Codes Initializing User Download Press the Line KEYUser Download Waiting HEX Dump ModeInitializing Online Adjusting the Print Quality Print DarknessCleaning the Print Head, Platen and Rollers Print SpeedCleaning the Label Edge Sensors Cleaning the Platen and RollersReplacing the Print Head Do not remove the two outside screws painted red Cleaning and Maintenance Using the IEEE1284 Parallel Interface Initial ChecklistC T I O N Tr o u b l e s h o o t i n g Introduction Using the RS232C Serial Interface Using the Lan Ethernet Interface Using the Universal Serial Bus USB InterfacePrinter does not Come UP Ready Intermittent Problems Checking the Network Connection and CablingLED LCD Message Audible Beep Error Condition Possible Causes GMTDPH-MAN Panduit TDP4*H C T I O N T e r f a c e Specification s Introduction Interface TypesSingle JOB Buffer Receive BufferMulti JOB Buffer IEEE1284 Parallel Interface Electrical Specifications PIN Signal DirectionIEEE1284 Parallel Interface Pin Assignments Data StreamsGeneral Specifications RS232 Serial InterfaceRS232C Interface Signals Signal DefinitionPIN Assignments PINREADY/BUSY Flow Control Cable RequirementsON/X-OFF Flow Control Local Area Network LAN Optional Interface Universal Serial Bus USB InterfaceBi-Directional Communications Cancel can ENQUIRE/ACK/NAKEnquire ENQ Print JOBPrint Stop DLE Print Start DC1Installation Error HandlingC T I O N T i o n a l Ac c e s s o r i e s Introduction Pcmcia Memory CardsError Description Indication Remedy Plug-In Interface ModulesCutter Operator SetupGeneral Operation Label Dispense Option Label Rewinder Removing and Unwinding the RollReal Time Clock