Manuals / Panduit / Computer Equipment / Printer

Panduit TDP43H, TDP42H, TDP46H manual HEX Dump Mode, User Download Waiting, Initializing Online

Models: TDP46H TDP43H TDP42H

1 84

Download 84 pages 23.38 Kb

Page 54

Section 3: Configuration

USER DOWNLOAD WAITING

HEX DUMP MODE

2.Press the LINE key. The printer is now waiting for the data to be sent.

3.Transmit the download data command stream to the printer.

4.After the data has been received, the printer will beep and print a status label. If it does not beep and print a status label, the printer did not accept the data.

5.If the printer did not beep and print a status label, turn the printer off and check your data stream for errors and start the download process over.

6.If the custom codes are correct, press the FEED key to accept them and terminate the download process. If they are incorrect, turn the printer off without pressing the ENTER key and begin the process again.

In addition to the Test Print Labels, the printer can print the contents of the receive buffer in a hexadecimal format to allow the data stream to be examined for errors and troubleshooting.

V05.00.03.00

INITIALIZING

ONLINE

QTY:000000

Displays the firmware during the initialization.

The Hex Dump Mode is entered by placing DSW2-4 in the on position and powering the printer on.

1.The printer is now ready to receive data.

2.Send the data stream to the printer.

3.The received data will be printed in a hexadecimal format4. To return the printer to normal operation, place DSW2-4 in the off position and power the printer off and then back on.

Page 3-28

GMTDPH-MAN

PANDUIT TDP4*H

Image 54

Panduit TDP43H, TDP42H, TDP46H manual HEX Dump Mode, User Download Waiting, Initializing Online

Contents

TDP42H, TDP43H, TDP46H Panduit Corp Cleaning and Maintenance InstallationConfiguration TroubleshootingInterface Specifications Optional AccessoriesC T I O N Pr i n t e r O v e r v i e w Introduction General Printer Specifications Specification TDP42H TDP43H TDP46H PrintSpecification Specification TDP42H TDP43H TDP46H Matrix Fonts Character FontsSymbologies Bar CodesPower PhysicalAccessories and Options GMTDPH-MAN Panduit TDP4*H C T I O N Installation Introduction Unpacking and Parts Identification Setting Up the Printer GMTDPH-MAN Panduit TDP4*H Loading Labels and Tags GMTDPH-MAN Panduit TDP4*H Panduit TDP4*H GMTDPH-MAN Loading the Ribbon Panduit TDP4*H GMTDPH-MAN Operator Panel LCD Display PanelOn Line Rear Panel EXTSensors Label Indexing SensorGMTDPH-MAN Panduit TDP4*H Setting DIP Switch PanelsRS232 TRANSMIT/RECEIVE Setting Setting DSW1Printer SET UP DSW2 OFFDSW2-2 Setting DSW3 Off Cutter Not UsedDSW3 OFF DSW3 OFFDSW3-6 DSW3-7 Software Default Settings Default SettingsSwitch Selections Default CompletedPotentiometer Adjustments PitchBackfeed Offset Display PrintLCD Panel Printer Configuration Normal ModeInitializing Online QTY000000 Offline Print DarknessPrint Speed Pitch Offset +00mm Advanced Mode Cancel Print JOB YES no CompletedInitializing Advanced Mode Zero Slash YES no Auto Online Print Offset SET Calendar YES noCalendar Ignore CR/LF YES noCard Mode Character Pitch Prop Fixed Advanced ModeCopy Start YES no Panduit TDP4*H CARD-MEMORY Copy Copying CARD-MEMORY Copy Copying Service Mode Initializing Advanced Mode Service Mode GAPX.XXV INPUTX.XVGAPX.XXV INPUTX.XV EYEX.XXV INPUTX.XV Auto Online Feed YES no Feed on Error Reprint W/FEED YES no FORWARD/BACKFEED Distance Default EXT PIN 9 Select MODE1 MODE2 Euro CodeACK Signal Service ModeCounters Mode Test Print ModeInitializing Default Setting Mode Initializing Default Setting YES noTest Print Size 10 CM Press Feed KEY to Stop Printing Download User Defined Protocol Codes Default Setting CompletedClear NON-STANDARD Protocol Initializing User Download Press the Line KEYHEX Dump Mode User Download WaitingInitializing Online Adjusting the Print Quality Print DarknessCleaning the Print Head, Platen and Rollers Print SpeedCleaning the Label Edge Sensors Cleaning the Platen and RollersReplacing the Print Head Do not remove the two outside screws painted red Cleaning and Maintenance Initial Checklist Using the IEEE1284 Parallel InterfaceC T I O N Tr o u b l e s h o o t i n g Introduction Using the RS232C Serial Interface Using the Universal Serial Bus USB Interface Using the Lan Ethernet InterfacePrinter does not Come UP Ready Intermittent Problems Checking the Network Connection and CablingLED LCD Message Audible Beep Error Condition Possible Causes GMTDPH-MAN Panduit TDP4*H C T I O N T e r f a c e Specification s Introduction Interface TypesReceive Buffer Single JOB BufferMulti JOB Buffer IEEE1284 Parallel Interface IEEE1284 Parallel Interface Pin Assignments Electrical SpecificationsPIN Signal Direction Data StreamsGeneral Specifications RS232 Serial InterfacePIN Assignments RS232C Interface SignalsSignal Definition PINCable Requirements READY/BUSY Flow ControlON/X-OFF Flow Control Universal Serial Bus USB Interface Local Area Network LAN Optional InterfaceBi-Directional Communications Enquire ENQ Cancel canENQUIRE/ACK/NAK Print JOBPrint Stop DLE Print Start DC1C T I O N T i o n a l Ac c e s s o r i e s Introduction InstallationError Handling Pcmcia Memory CardsError Description Indication Remedy Plug-In Interface ModulesOperator Setup CutterGeneral Operation Label Dispense Option Label Rewinder Removing and Unwinding the RollReal Time Clock