Manuals / Panduit / Computer Equipment / Printer

Panduit TDP43H, TDP42H, TDP46H manual IEEE1284 Parallel Interface

Models: TDP46H TDP43H TDP42H

1 84

Download 84 pages 23.38 Kb

Page 69

Section 6: Interface Specifications

0

2.0 MB

2.95 MB

DTR High

or

DTR Low

X-On

or

Buffer Near Full

X-Off

The receiving buffer will not be able to receive more data again until a “Buffer Available” condition occurs. This takes place when the receiving buffer has emptied so that only 1 MB bytes of data are being held (2.0 MB bytes from being full). At this time, DTR will go “high” or an X-On is sent to tell the host that it can again receive data.

0		1.0 MB			2.95 MB

DTR Low

or

X-Off

DTR High

or

X-On

Buffer Available

All printer error conditions (i.e., label out, ribbon out) will cause the printer to go busy (DTR “low” or X-Off) until the problem is corrected and the printer is placed on-line. The printer will also be busy if taken off-line from the front panel.

IEEE1284 Parallel Interface

The parallel interface for the TDP4*H printers is a Plug-In Interface Module that can be installed by the user. It conforms to the IEEE1284 specification. It will automatically detect the IEEE1284 signals and operate in the high speed mode. If it does not detect the IEEE1284 signals, it will operate in the standard Centronics mode, which is significantly slower. For this reason, an interface cable and host interface conforming to the IEEE1284 specification must be present to fully utilize the speed capabilities. This interface also operates bi-directionally and can report the status of the printer back to the host.

PANDUIT TDP4*H

GMTDPH-MAN

Page 6-3

Image 69

Panduit TDP43H, TDP42H, TDP46H manual IEEE1284 Parallel Interface

Contents

TDP42H, TDP43H, TDP46H Panduit Corp Configuration InstallationCleaning and Maintenance TroubleshootingOptional Accessories Interface SpecificationsC T I O N Pr i n t e r O v e r v i e w Introduction Specification TDP42H TDP43H TDP46H Print General Printer SpecificationsSpecification Character Fonts Specification TDP42H TDP43H TDP46H Matrix FontsBar Codes SymbologiesPhysical PowerAccessories and Options GMTDPH-MAN Panduit TDP4*H C T I O N Installation Introduction Unpacking and Parts Identification Setting Up the Printer GMTDPH-MAN Panduit TDP4*H Loading Labels and Tags GMTDPH-MAN Panduit TDP4*H Panduit TDP4*H GMTDPH-MAN Loading the Ribbon Panduit TDP4*H GMTDPH-MAN LCD Display Panel Operator PanelOn Line EXT Rear PanelLabel Indexing Sensor SensorsGMTDPH-MAN Panduit TDP4*H RS232 TRANSMIT/RECEIVE Setting DIP Switch PanelsSetting Setting DSW1DSW2 OFF Printer SET UPDSW2-2 Off Cutter Not Used Setting DSW3DSW3 OFF DSW3 OFFDSW3-6 DSW3-7 Switch Selections Default SettingsSoftware Default Settings Default CompletedPotentiometer Adjustments PitchBackfeed Offset Print DisplayLCD Panel Printer Configuration Normal ModeInitializing Online QTY000000 Offline Print DarknessPrint Speed Pitch Offset +00mm Advanced Mode Cancel Print JOB YES no CompletedInitializing Advanced Mode Zero Slash YES no Auto Online SET Calendar YES no Print OffsetIgnore CR/LF YES no CalendarCard Mode Character Pitch Prop Fixed Advanced ModeCopy Start YES no Panduit TDP4*H CARD-MEMORY Copy Copying CARD-MEMORY Copy Copying Initializing Advanced Mode Service Mode GAPX.XXV INPUTX.XV Service ModeGAPX.XXV INPUTX.XV EYEX.XXV INPUTX.XV Auto Online Feed YES no Feed on Error EXT PIN 9 Select MODE1 MODE2 Euro Code Reprint W/FEED YES no FORWARD/BACKFEED Distance DefaultService Mode ACK SignalCounters Mode Test Print ModeInitializing Default Setting Mode Initializing Default Setting YES noTest Print Size 10 CM Press Feed KEY to Stop Printing Clear NON-STANDARD Protocol Default Setting CompletedDownload User Defined Protocol Codes Initializing User Download Press the Line KEYHEX Dump Mode User Download WaitingInitializing Online Print Darkness Adjusting the Print QualityPrint Speed Cleaning the Print Head, Platen and RollersCleaning the Platen and Rollers Cleaning the Label Edge SensorsReplacing the Print Head Do not remove the two outside screws painted red Cleaning and Maintenance Initial Checklist Using the IEEE1284 Parallel InterfaceC T I O N Tr o u b l e s h o o t i n g Introduction Using the RS232C Serial Interface Using the Universal Serial Bus USB Interface Using the Lan Ethernet InterfacePrinter does not Come UP Ready Checking the Network Connection and Cabling Intermittent ProblemsLED LCD Message Audible Beep Error Condition Possible Causes GMTDPH-MAN Panduit TDP4*H Interface Types C T I O N T e r f a c e Specification s IntroductionReceive Buffer Single JOB BufferMulti JOB Buffer IEEE1284 Parallel Interface PIN Signal Direction Electrical SpecificationsIEEE1284 Parallel Interface Pin Assignments Data StreamsRS232 Serial Interface General SpecificationsSignal Definition RS232C Interface SignalsPIN Assignments PINCable Requirements READY/BUSY Flow ControlON/X-OFF Flow Control Universal Serial Bus USB Interface Local Area Network LAN Optional InterfaceBi-Directional Communications ENQUIRE/ACK/NAK Cancel canEnquire ENQ Print JOBPrint Start DC1 Print Stop DLEError Handling InstallationC T I O N T i o n a l Ac c e s s o r i e s Introduction Pcmcia Memory CardsPlug-In Interface Modules Error Description Indication RemedyOperator Setup CutterGeneral Operation Label Dispense Option Removing and Unwinding the Roll Label RewinderReal Time Clock