Assembly Steps | Precor 5.33, 5.23 guide

Assembly Steps

Feed the display cable through the upright support.

Important: Do not stretch, crimp, or damage the cable. Cables damaged by improper installation will not be covered by the Precor Limited Warranty.

Attach the display console to the upright support using four Phillips-head screws (A).

Thread the display cable through the grommet and out the front of the base tube. Plug the cable connector into its receptacle.

Important: Important: If the plastic grommet pops out of the base, replace it immediately. The grommet covers the metal edges so the cables are not cut or damaged.

Align the mounting holes and secure the upright support to the base using two hex head screws (D) and two washers

(E). Finger tighten.

Push excess cable into the base tube.

CAUTION: Be aware of a sharp screw inside the base tube. Abrasive cuts or other injuries can occur if you place your hands, fingers, bare feet, or toes inside the base tube.

Lift the EFX. Slide a wedge of packing material under the front of the unit.

EFX5.33 Elliptical Fitness Trainer Assembly Guide

4

Image 64

Precor 5.33, 5.23 manual Assembly Steps

Contents

Page Page Important Safety Instructions Safety Approval Do not use outdoors Grounding Instructions Units Designated for U.S. Markets Radio Frequency Interference RFI Federal Communications Commission, PartCanadian Department of Communications Débranchez avant de réparer Obtaining Service Table of Contents Precor Residential Equipment EFX Safety Features Locking Pin Using the Stationary Handrail Turning the Unit on and OFF 114 Guidelines Using SmartRate Exercise to Your Target Heart Rate LED Display Console Page 1532 Scanning and the Display CrossRamp Display on the EFX5.23 Keypad Quickstart Shows the degree of incline for each CrossRamp setting Changing the Display Features Using the Select Key 1532 132Page Precor Choosing Quickstart User Selecting a User ID Selecting a Program Dist Cooling Down After a Workout Pausing During a Workout or the Cool-Down Period Ending a Workout Programs Choosing a Program Table below shows a variety of program options Program Tips ManlManual Manl Program Xctr Crosstraining Xctr Program Glut Hill Gluteal Glut Program Hill Climb Hill Program INT1 Interval INTn Program Random Rand Program Weight Loss Wtls Program Rand Wtls Fitn Fitness Test Fitn Guidelines Warm-up Period Completing the Fitness Test Using the Fitness TestFitness Test Scores Cardiorespiratory Fitness Score Category-Females HRC Heart Rate Control HRC Program CST1 Using the HRC ProgramCustom CST1 or CST2 Programs Clearing the Settings on a Custom Program Cals Dist Calories Cals Program Distance Dist Program Advanced Programming and Troubleshooting Advanced Programming Tips RESET, QUICKSTART, ENTER, Select User 2, Crossramp Selecting a U.S. Standard or Metric Display Informational Displays Viewing the OdometerViewing the Hour Meter Viewing the Software Version and Part Numbers Viewing the Error Log Key Description Displaying the Serial Number Troubleshooting Error Codes Troubleshooting Heart Rate Cleaning the Equipment Inspection Servicing the EFX Storing the Chest StrapLong-Term Storage Warranty Periods and Coverage Limited WarrantyOptions / Accessories Conditions and Restrictions This limited warranty shall not apply toDisclaimer and Release Exclusive Remedies Exclusion of Consequential and Incidental Damages Thank You and Welcome to Precor Tell US about Your NEW Precor Product Product Specifications EFX5.23/EFX5.33 Elliptical Fitness CrosstrainersPage User ID Keys Locking Pin on the Roller Arm Choose a Program Assembly Guide Obtaining Service Unpacking the Equipment Hardware Kit not shown to scale Fasteners Quantity Assembly Steps EFX5.33 Elliptical Fitness Trainer Assembly Guide EFX5.33 Elliptical Fitness Trainer Assembly Guide EFX5.33 Elliptical Fitness Trainer Assembly Guide Have your assistant carefully lower the unit to the floor