To start a ConfiguRAD session | RAD Data comm RIC-155 specification

Chapter 3 Operation	RIC-155Installation and Operation Manual

Cautions

Notes

Note

•Make sure the Ethernet management ports of the local and remote devices are connected to different LANs.

•Do not run diagnostic loopbacks on RIC-155 or insert loopback plugs into its Ethernet ports.

•When RIC-155 is managed over Telnet or ConfiguRAD, only two simultaneous management sessions are allowed. An additional management session can be opened from the supervisory terminal.

•If no user input is detected for 10 minutes during Telnet or ConfiguRAD session, RIC-155 automatically disconnects from the management station.

•ConfiguRAD management utility is compatible with Internet Explorer 6.0 and above.

To start a ConfiguRAD session:

1.Start a Web browser.

2.Disable any pop-up blocking software, such as Google Popup Blocker.

3.In the address bar, enter an IP address of RIC-155, and press <Enter>. The Login screen appears.

4.In the Login screen, click Login to start the ConfiguRAD management session.

Disable the proxy server connection for the Web browser to ensure stable ConfiguRAD session.

3-6	Configuration Alternatives

Image 32

RAD Data comm RIC-155 operation manual To start a ConfiguRAD session

Contents

RIC-155 Page RIC-155 Limited Warranty General Safety Instructions Please observe the following precautions Connection of DC Mains General Safety PracticesConnection of AC Mains Ports Safety Status Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Conventions Safety Manufacturers Name Manufacturers AddressProduct Name Supplementary Information Quick Start Guide Installing RIC-155Configuring RIC-155 Configuring RIC-155 To configure RIC-155 Contents Troubleshooting and Diagnostics Appendix A. Connector Wiring Appendix B. Traffic Separation Chapter Introduction OverviewVersions Application Features 10/100BaseT InterfaceSTM-1/OC-3c Interface Fiber Optic Interface Options Alarm Relay ManagementInternal Bridge Status Reporting Physical Description RIC-155 3D View RIC-155 Block Diagram Functional Description Technical Specifications Alarm Types Major and minor Connector DB-9, female Temperature 50C / 32-122F Humidity Up to 90%, non-condensing Introduction Site Requirements and Prerequisites Chapter Installation and SetupIntroduction Package Contents Connecting the Interface Cables Connecting DC Power Connecting the Power CableConnecting AC Power Connecting the Power Cable Controls and Indicators Chapter OperationTurning On RIC-155 To turn on RIC-155 RIC-155 Normal Indicator Status Indicator StatusRIC-155 LEDs Name Function Location Default Settings RIC-155 Default Settings Configuration Alternatives Parameter Default ValueManaging RIC-155 via Terminal Port Uplink Managing RIC-155 via Ethernet Ports Preparing the TerminalStarting Terminal Session for a First Time To prepare RIC-155 for network management To start a ConfiguRAD session Loging on To enter the user name and passwordNavigating the Management Menus Menu Map To choose an option ConfiguRAD session Choosing OptionsCorrecting Entries To choose an option terminal session Logging Out Turning Off RIC-155Navigating Tables Operation Turning Off RIC-155 Chapter Configuration Configuring RIC-155 for ManagementTo access the Configuration menu To access the Management menu Entering Device Information To enter device information Configuring the Host Parameters To define the IP parameters Configuring the Network Managers To configure the network managers Controlling the Management Access To define the management access method Configuring the RIC-155 for Operation To enable or disable management ports Configuring the Clock Source Configuring Control Port Parameters Changing the Control Port Data Rate Enabling and Disabling Pop-up AlarmsConfiguring the Security Timeout Configuring the STM-1/OC-3c Interface Configuring the Physical PortsConfiguring the Ethernet Interface J1 Path Trace 10E-3,10E-4,10E-510E-5,10E-6,10E-7,10E-8,10E-9 Uplink Port Signal Loss Line Excessive Error DefectLine Signal Degraded Error Uplink Port Loss of Signal Configuring the Internal Bridge Configuring Fast Ethernet BridgeTo configure the Fast Ethernet bridge Mbps, 8 Mbps, No Limit Configuring the Bridge Ports Configuring Ethernet Management and Data Bridge PortsTo access the Bridge Port menu To configure the Ethernet management and data bridge ports Configuring the POS Bridge Port To configure the POS port To display the system information Displaying the RIC-155 StatusDisplaying the System Status To display the Ethernet port status Displaying the Port StatusDisplaying the Ethernet Port Status Displaying the STM-1/OC-3c Port Status DATA/MNG Port Status ParametersTo display the STM-1/OC-3c port status Parameters Values Changing the Password To change the current passwordAdditional Tasks STM-1/OC-3c Port Status Parameters 21. User Access Menu Displaying the RIC-155 Inventory To install a new software release via Tftp Installing Software ReleasesInstalling a New Software Release via Tftp Installing a New Software Release via Xmodem To install a new software release via Xmodem Transferring Configuration Files To upload a configuration fileTo download a configuration file Displaying the Software Version To switch software versions Switching Software VersionsResetting RIC-155 Resetting RIC-155 to Factory Defaults Resetting RIC-155To reset RIC-155 to the defaults To reset RIC-155 Chapter Troubleshooting Diagnostics Monitoring PerformanceDisplaying the Ethernet Statistics To display the Ethernet statistics Displaying SDH/SONET Statistics To display the current SDH/SONET statistics Uplink Statistics Screen, Display Description Range Uasl RCV Abort To display SDH/SONET statistics for all intervals 1explains all SDH/SONET statistics parameters Detecting Errors Handling AlarmsPower-Up Self-Test Front Panel LEDs Displaying System Alarms To display the system alarmsWorking with the Log File To display the event log file To clear the event log Configuring Alarm SeverityTo configure the alarm severity Masking Port Alarms To mask RIC-155 alarmsRIC-155 Alarms and Warnings Terminal Message Description Severity RIC-155 Events Number Terminal Message Description Troubleshooting and Diagnostics Handling Alarms Appendix a Connector Wiring Ethernet ConnectorsAlarm Relay Connector Table A-1. ETH and MNG-ETH Connector Pinout Control Connector Table A-2. Alarm Connector PinoutTable A-3. Control Connector Pinout Pin Alarm Relay Function Appendix B Traffic Separation Port-Based Traffic SeparationNone MNG only Local Mng Only Port-Based/VLAN-Based Traffic SeparationAll Default Tagging Table B-1. Default Tagging ModesTagging Modes of the Bridge Ports Uplink and Host Ports Forwarding Mode Port Filter Management Access Mode None MNG Only All Local MNG OnlyInternal Operation Modes of the Bridge Ports None MNG Only All Local MNG Only Configuring for a Typical ApplicationManaging RIC-155 via MNG Port Managing RIC-155 via Data Port Figure B-9. Managing RIC-155 via MNG Port Figure B-10. Managing RIC-155 via Data Port Index RADview-Lite,3-5 STM-1/OC-3c interface, 1-2,1-6 Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters