RAD Data comm RIC-155 - page 47

RIC-155 Installation and Operation Manual Chapter 4 Configuration

Configuring the Physical Ports 4-11

The following alarms trigger an uplink failure:

• Uplink Port Signal Loss

• Line Excessive Error Defect

• Line Signal Degraded Error

• Uplink Port Loss of Signal

• Uplink Port Loss of Frame

• Path Rx Facility Pointer Loss

• Path Excessive Error Defect

• Path Signal Degraded Error

• Path Trace J1 string mismatch.

With Physical Failure Forwarding enabled, three additional alarms trigger an uplink

failure:

• Line Alarm Indication Signal (AIS-L)

• Remote Line Defect Indication (RDI-L)

• Unequipped.

It is possible to mask errors in the Alarm Setup menu, so that the uplink will not be

interrupted. (See Chapter 5)

RIC-155

Uplink Configuration

1. Uplink Mode: (SDH)

2. BER Threshold: (Enabled)

3. EED Threshold (10E-): > (10E-3)

4. SD Threshold (10E-): > (10E-6)

5. J1 Path Trace Configuration: >

6. Send AIS-L (K2)... (Enabled)

7. Send Unequipped (C2) (Enabled)

8. Physical failure forwarding (Enabled)

8. Physical failure forwarding on RDI-L/AIS-L/Unequipped (Disabled)

Please select item <1 to 8>

ESC-prev.menu; !-main menu; &-exit

Figure 4-13. Uplink Configuration Menu

• Item 9 of Figure 4-13, appears only when item 8, Physical failure forwarding, is

enabled.

• If item 9 is enabled, RIC-155 considers the RDI-L/AIS-L/Unequipped status in

addition to all the other alarms in physical failure forwarding.

Note

Note

Contents

Main Page RIC-155 10/100BaseT to STM-1/OC-3 Converter Version 1.12 Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Caution Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Warning Conventions Declaration of Conformity Quick Start Guide 1. Installing RIC-155 Connecting the Interfaces Connecting the Power 2. Configuring RIC-155 Configuring RIC-155 Contents Page Chapter 1 Introduction 1.1 Overview Versions STM-1/OC-3c Interface Options Power Supply Options Features 10/100BaseT Interface STM-1/OC-3c Interface Management Internal Bridge Alarm Relay Status Reporting 1.2 Physical Description 1.3 Functional Description 1.4 Technical Specifications Page Page Chapter 2 Installation and Setup 2.1 Introduction 2.2 Site Requirements and Prerequisites 2.3 Package Contents 2.4 Connecting the Interface Cables Connecting the STM-1/OC-3c Interface Connecting the 10/100BaseT Interface 2.5 Connecting the Power Cable Connecting AC Power Connecting DC Power Page Chapter 3 Operation 3.1 Turning On RIC-155 3.2 Controls and Indicators Page 3.3 Default Settings 3.4 Configuration Alternatives Managing RIC-155 via Terminal Port Preparing the Terminal Starting Terminal Session for a First Time Managing RIC-155 via Ethernet Ports Notes Cautions Note 3.5 Navigating the Management Menus Menu Map Loging on Choosing Options Correcting Entries Navigating Tables Logging Out 3.6 Turning Off RIC-155 Page Chapter 4 Configuration 4.1 Configuring RIC-155 for Management Entering Device Information Configuring the Host Parameters Configuring the Network Managers Controlling the Management Access 4.2 Configuring the RIC-155 for Operation Configuring the Clock Source Configuring Control Port Parameters Changing the Control Port Data Rate Configuring the Security Timeout Enabling and Disabling Pop-up Alarms 4.3 Configuring the Physical Ports Configuring the Ethernet Interface Configuring the STM-1/OC-3c Interface Page Page 4.4 Configuring the Internal Bridge Configuring Fast Ethernet Bridge Configuring the Bridge Ports Configuring Ethernet Management and Data Bridge Ports Configuring the POS Bridge Port 4.5 Displaying the RIC-155 Status Displaying the System Status Displaying the Port Status Displaying the Ethernet Port Status Displaying the STM-1/OC-3c Port Status 4.6 Additional Tasks Changing the Password Displaying the RIC-155 Inventory Installing Software Releases Installing a New Software Release via TFTP Installing a New Software Release via XMODEM Transferring Configuration Files Displaying the Software Version Switching Software Versions Resetting RIC-155 Resetting RIC-155 to Factory Defaults Resetting RIC-155 Chapter 5 Troubleshooting and Diagnostics 5.1 Monitoring Performance Displaying the Ethernet Statistics Displaying SDH/SONET Statistics Figure 5-4. Uplink Statistics Screen, Page 1 Figure 5-5. Uplink Statistics Screen, Page 2 Table 5-1. SDH/SONET Statistics Parameters Page Page Page 5.2 Detecting Errors Power-Up Self-Test Front Panel LEDs 5.3 Handling Alarms Displaying System Alarms Working with the Log File Configuring Alarm Severity Figure 5-13. System Alarms Menu Masking Port Alarms RIC-155 management software allows you to mask alarms to prevent them from being reported. Table 5-3. RIC-155 Events Page Appendix A Connector Wiring A.1 Ethernet Connectors A.2 Alarm Relay Connector A.3 Control Connector Appendix B Traffic Separation B.1 Port-Based Traffic Separation None MNG only All B.2 Port-Based/VLAN-Based Traffic Separation Tagging Modes of the Bridge Ports Uplink and Host Ports Management and Data Ports Default Tagging Internal Operation Modes of the Bridge Ports Traffic Separation according to the Management Access and VLANs None MNG Only All Local MNG Only B.3 Configuring for a Typical Application Managing RIC-155 via MNG Port Managing RIC-155 via Data Port Page Index Page Customer Response Form Page Error Report