Features, 10/100BaseT Interface | RAD Data comm RIC-155 instruction

Chapter 1 Introduction	RIC-155Installation and Operation Manual

Features

10/100BaseT Interface

RIC-155 Fast Ethernet interface operation conforms to the IEEE 802.3u, 802.3x and 802.1p standards, including VLAN applications. The Fast Ethernet interface supports the following functions:

•Four levels of QoS, according to ToS or 802.3p

•High performance lookup engine with support for up to 1024 MAC address entries with automatic learning and aging

•Autonegotiation

•Backpressure

•Half duplex and full duplex operation

•FDX flow control

•Automatic MDI/MDIX crossover.

STM-1/OC-3c Interface

RIC-155 converts Ethernet/Fast Ethernet signals into POS and vice. The STM-1/OC-3c interface terminates into fiber optic or 75Ω BNC coaxial connectors. Single mode fiber optic interface of the unit uses a 1310 nm LED or 1310/1550 laser diode transmitters (see Table 1-1).

The STM-1/OC-3c interface of RIC-155 operates with internal or receive clock.

Table 1-1. Fiber Optic Interface Options

Wavelength	Fiber Type	Transmitter	Power	Receiver	Typical Max.	Connector
		Type		Sensitivity	Range
[nm]	[∝m]		[dBm]	[dBm]	[km/miles]

1310	62.5/125,	LED	-18	-31	2/1.2	SC
	multimode

1310	9/125 single mode	Laser	-12	-31	20/12.4	ST, SC, FC

1310	9/125 single mode	Laser, long haul	-2	-34	40/25	ST, SC, FC

1550	9/125 single mode	Laser, long haul	-2	-34	80/49.7	SC

SF1 (WDM)	9/125 single mode	Laser	-12	-29	20/12.4	SC
		Tx – 1310
		Rx – 1550
SF2 (WDM)	9/125 single mode	Laser	-12	-29	20/12.4	SC
		Tx – 1550
		Rx – 1310
SF3	9/125 single mode	Laser, 1310	-12	-27	20/12.4	SC/APC
(single fiber)		Tx and Rx

1-2 Overview

Image 16

RAD Data comm RIC-155 Features, 10/100BaseT Interface, STM-1/OC-3c Interface, Fiber Optic Interface Options

Contents

RIC-155 Page RIC-155 Limited Warranty General Safety Instructions Please observe the following precautions Connection of AC Mains General Safety PracticesConnection of DC Mains Ports Safety Status Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Conventions Safety Manufacturers Name Manufacturers AddressProduct Name Supplementary Information Configuring RIC-155 Installing RIC-155Quick Start Guide Configuring RIC-155 To configure RIC-155 Contents Troubleshooting and Diagnostics Appendix A. Connector Wiring Appendix B. Traffic Separation Chapter Introduction OverviewVersions Application Features 10/100BaseT InterfaceSTM-1/OC-3c Interface Fiber Optic Interface Options Alarm Relay ManagementInternal Bridge Status Reporting Physical Description RIC-155 3D View RIC-155 Block Diagram Functional Description Technical Specifications Alarm Types Major and minor Connector DB-9, female Temperature 50C / 32-122F Humidity Up to 90%, non-condensing Introduction Introduction Chapter Installation and SetupSite Requirements and Prerequisites Package Contents Connecting the Interface Cables Connecting AC Power Connecting the Power CableConnecting DC Power Connecting the Power Cable Controls and Indicators Chapter OperationTurning On RIC-155 To turn on RIC-155 RIC-155 Normal Indicator Status Indicator StatusRIC-155 LEDs Name Function Location Default Settings RIC-155 Default Settings Configuration Alternatives Parameter Default ValueManaging RIC-155 via Terminal Port Uplink Managing RIC-155 via Ethernet Ports Preparing the TerminalStarting Terminal Session for a First Time To prepare RIC-155 for network management To start a ConfiguRAD session Loging on To enter the user name and passwordNavigating the Management Menus Menu Map To choose an option ConfiguRAD session Choosing OptionsCorrecting Entries To choose an option terminal session Navigating Tables Turning Off RIC-155Logging Out Operation Turning Off RIC-155 Chapter Configuration Configuring RIC-155 for ManagementTo access the Configuration menu To access the Management menu Entering Device Information To enter device information Configuring the Host Parameters To define the IP parameters Configuring the Network Managers To configure the network managers Controlling the Management Access To define the management access method Configuring the RIC-155 for Operation To enable or disable management ports Configuring the Clock Source Configuring Control Port Parameters Configuring the Security Timeout Enabling and Disabling Pop-up AlarmsChanging the Control Port Data Rate Configuring the Ethernet Interface Configuring the Physical PortsConfiguring the STM-1/OC-3c Interface 10E-5,10E-6,10E-7,10E-8,10E-9 10E-3,10E-4,10E-5J1 Path Trace Uplink Port Signal Loss Line Excessive Error DefectLine Signal Degraded Error Uplink Port Loss of Signal Configuring the Internal Bridge Configuring Fast Ethernet BridgeTo configure the Fast Ethernet bridge Mbps, 8 Mbps, No Limit Configuring the Bridge Ports Configuring Ethernet Management and Data Bridge PortsTo access the Bridge Port menu To configure the Ethernet management and data bridge ports Configuring the POS Bridge Port To configure the POS port Displaying the System Status Displaying the RIC-155 StatusTo display the system information Displaying the Ethernet Port Status Displaying the Port StatusTo display the Ethernet port status Displaying the STM-1/OC-3c Port Status DATA/MNG Port Status ParametersTo display the STM-1/OC-3c port status Parameters Values Changing the Password To change the current passwordAdditional Tasks STM-1/OC-3c Port Status Parameters 21. User Access Menu Displaying the RIC-155 Inventory Installing a New Software Release via Tftp Installing Software ReleasesTo install a new software release via Tftp Installing a New Software Release via Xmodem To install a new software release via Xmodem Transferring Configuration Files To upload a configuration fileTo download a configuration file Displaying the Software Version Resetting RIC-155 Switching Software VersionsTo switch software versions Resetting RIC-155 to Factory Defaults Resetting RIC-155To reset RIC-155 to the defaults To reset RIC-155 Chapter Troubleshooting Diagnostics Monitoring PerformanceDisplaying the Ethernet Statistics To display the Ethernet statistics Displaying SDH/SONET Statistics To display the current SDH/SONET statistics Uplink Statistics Screen, Display Description Range Uasl RCV Abort To display SDH/SONET statistics for all intervals 1explains all SDH/SONET statistics parameters Detecting Errors Handling AlarmsPower-Up Self-Test Front Panel LEDs Displaying System Alarms To display the system alarmsWorking with the Log File To display the event log file To configure the alarm severity Configuring Alarm SeverityTo clear the event log Masking Port Alarms To mask RIC-155 alarmsRIC-155 Alarms and Warnings Terminal Message Description Severity RIC-155 Events Number Terminal Message Description Troubleshooting and Diagnostics Handling Alarms Appendix a Connector Wiring Ethernet ConnectorsAlarm Relay Connector Table A-1. ETH and MNG-ETH Connector Pinout Control Connector Table A-2. Alarm Connector PinoutTable A-3. Control Connector Pinout Pin Alarm Relay Function Appendix B Traffic Separation Port-Based Traffic SeparationNone MNG only All Port-Based/VLAN-Based Traffic SeparationLocal Mng Only Default Tagging Table B-1. Default Tagging ModesTagging Modes of the Bridge Ports Uplink and Host Ports Forwarding Mode Port Filter Management Access Mode None MNG Only All Local MNG OnlyInternal Operation Modes of the Bridge Ports None MNG Only All Managing RIC-155 via MNG Port Configuring for a Typical ApplicationLocal MNG Only Managing RIC-155 via Data Port Figure B-9. Managing RIC-155 via MNG Port Figure B-10. Managing RIC-155 via Data Port Index RADview-Lite,3-5 STM-1/OC-3c interface, 1-2,1-6 Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters