Configuration Alternatives, Uplink, Bridge | RAD Data comm RIC-155

Chapter 3 Operation		RIC-155Installation and Operation Manual


	Parameter	Default Value

	Flow control	Enable

	Ethernet mode	Full duplex

	LAN speed	100 Mbps

	Uplink

	Frame type	SONET

	BER threshold	Disable

	EED threshold	10E-3
	SD threshold	10E-6
	J1 Tx path trace enable	Disable

	J1 path trace

	Physical Failure Forwarding	Disable

	Bridge

	Aging Time	304

	Forwarding Mode	Filter

	Statistics Counted	OK only

	Multicast & Broadcast Rate	No Limit
	Limit

	DATA Port PVID	2

	DATA Port PVID Priority	0

	DATA Port Tag Stripping	No

	MNG Port PVID	1

	MNG Port PVID Priority	0

	MNG Port Tag Stripping	No

	POS Port Egress	Unmodified

3.4Configuration Alternatives

Managing RIC-155 via Terminal Port

RIC-155 includes a V.24/RS-232 asynchronous DTE port, designated CONTROL and terminated in a 9-pin D-type female connector. The control port continuously monitors the incoming data stream and immediately responds to any input string received through this port. The port requires a cross-cable for the ASCII terminal connection.

The RIC-155 control port can be configured to communicate at the following rates: 9.6, 19.2, 38.4, 57.6 or 115.2 kbps. When running a terminal control

3-4	Configuration Alternatives

Image 30

RAD Data comm Configuration Alternatives, Managing RIC-155 via Terminal Port, Parameter Default Value, Uplink, Bridge

Contents

RIC-155 Page RIC-155 Limited Warranty General Safety Instructions Please observe the following precautions General Safety Practices Connection of AC MainsConnection of DC Mains Ports Safety Status Connection of Data and Telecommunications Cables Electromagnetic Compatibility EMC Canadian Emission Requirements Conventions Product Name SafetyManufacturers Name Manufacturers Address Supplementary Information Installing RIC-155 Configuring RIC-155Quick Start Guide Configuring RIC-155 To configure RIC-155 Contents Troubleshooting and Diagnostics Appendix A. Connector Wiring Appendix B. Traffic Separation Versions Chapter IntroductionOverview Application STM-1/OC-3c Interface Features10/100BaseT Interface Fiber Optic Interface Options Internal Bridge Alarm RelayManagement Status Reporting Physical Description RIC-155 3D View RIC-155 Block Diagram Functional Description Technical Specifications Alarm Types Major and minor Connector DB-9, female Temperature 50C / 32-122F Humidity Up to 90%, non-condensing Introduction Chapter Installation and Setup IntroductionSite Requirements and Prerequisites Package Contents Connecting the Interface Cables Connecting the Power Cable Connecting AC PowerConnecting DC Power Connecting the Power Cable Turning On RIC-155 Controls and IndicatorsChapter Operation To turn on RIC-155 RIC-155 LEDs RIC-155 Normal Indicator StatusIndicator Status Name Function Location Default Settings RIC-155 Default Settings Managing RIC-155 via Terminal Port Configuration AlternativesParameter Default Value Uplink Starting Terminal Session for a First Time Managing RIC-155 via Ethernet PortsPreparing the Terminal To prepare RIC-155 for network management To start a ConfiguRAD session Navigating the Management Menus Loging onTo enter the user name and password Menu Map Correcting Entries To choose an option ConfiguRAD sessionChoosing Options To choose an option terminal session Turning Off RIC-155 Navigating TablesLogging Out Operation Turning Off RIC-155 To access the Configuration menu Chapter ConfigurationConfiguring RIC-155 for Management To access the Management menu Entering Device Information To enter device information Configuring the Host Parameters To define the IP parameters Configuring the Network Managers To configure the network managers Controlling the Management Access To define the management access method Configuring the RIC-155 for Operation To enable or disable management ports Configuring the Clock Source Configuring Control Port Parameters Enabling and Disabling Pop-up Alarms Configuring the Security TimeoutChanging the Control Port Data Rate Configuring the Physical Ports Configuring the Ethernet InterfaceConfiguring the STM-1/OC-3c Interface 10E-3,10E-4,10E-5 10E-5,10E-6,10E-7,10E-8,10E-9J1 Path Trace Line Signal Degraded Error Uplink Port Signal LossLine Excessive Error Defect Uplink Port Loss of Signal To configure the Fast Ethernet bridge Configuring the Internal BridgeConfiguring Fast Ethernet Bridge Mbps, 8 Mbps, No Limit To access the Bridge Port menu Configuring the Bridge PortsConfiguring Ethernet Management and Data Bridge Ports To configure the Ethernet management and data bridge ports Configuring the POS Bridge Port To configure the POS port Displaying the RIC-155 Status Displaying the System StatusTo display the system information Displaying the Port Status Displaying the Ethernet Port StatusTo display the Ethernet port status To display the STM-1/OC-3c port status Displaying the STM-1/OC-3c Port StatusDATA/MNG Port Status Parameters Parameters Values Additional Tasks Changing the PasswordTo change the current password STM-1/OC-3c Port Status Parameters 21. User Access Menu Displaying the RIC-155 Inventory Installing Software Releases Installing a New Software Release via TftpTo install a new software release via Tftp Installing a New Software Release via Xmodem To install a new software release via Xmodem To download a configuration file Transferring Configuration FilesTo upload a configuration file Displaying the Software Version Switching Software Versions Resetting RIC-155To switch software versions To reset RIC-155 to the defaults Resetting RIC-155 to Factory DefaultsResetting RIC-155 To reset RIC-155 Displaying the Ethernet Statistics Chapter Troubleshooting DiagnosticsMonitoring Performance To display the Ethernet statistics Displaying SDH/SONET Statistics To display the current SDH/SONET statistics Uplink Statistics Screen, Display Description Range Uasl RCV Abort To display SDH/SONET statistics for all intervals 1explains all SDH/SONET statistics parameters Power-Up Self-Test Detecting ErrorsHandling Alarms Front Panel LEDs Working with the Log File Displaying System AlarmsTo display the system alarms To display the event log file Configuring Alarm Severity To configure the alarm severityTo clear the event log RIC-155 Alarms and Warnings Masking Port AlarmsTo mask RIC-155 alarms Terminal Message Description Severity RIC-155 Events Number Terminal Message Description Troubleshooting and Diagnostics Handling Alarms Alarm Relay Connector Appendix a Connector WiringEthernet Connectors Table A-1. ETH and MNG-ETH Connector Pinout Table A-3. Control Connector Pinout Control ConnectorTable A-2. Alarm Connector Pinout Pin Alarm Relay Function None Appendix B Traffic SeparationPort-Based Traffic Separation MNG only Port-Based/VLAN-Based Traffic Separation AllLocal Mng Only Tagging Modes of the Bridge Ports Default TaggingTable B-1. Default Tagging Modes Uplink and Host Ports Internal Operation Modes of the Bridge Ports Forwarding Mode Port FilterManagement Access Mode None MNG Only All Local MNG Only None MNG Only All Configuring for a Typical Application Managing RIC-155 via MNG PortLocal MNG Only Managing RIC-155 via Data Port Figure B-9. Managing RIC-155 via MNG Port Figure B-10. Managing RIC-155 via Data Port Index RADview-Lite,3-5 STM-1/OC-3c interface, 1-2,1-6 Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters