Manuals / Radio Shack / Computer Equipment / Scanner

Radio Shack PRO-528 manual Programming trunked frequencies, You See Trunk System

Models: PRO-528

1 92

Download 92 pages 20.09 Kb

Page 53

Beyond the Basics

the scanner. If it is set too high, it could prevent your scanner from locking on the control channel reliably. If it is set too low, it will slightly delay ﬁnding the control channel. The best setting is the same as for conventional reception and is critical for monitoring trunked systems.

programming trunked frequencies

Follow these steps to select, program, and store trunked frequencies.

1.Press E/PGM in conventional mode to set the scanner in programming mode. Then, press TRUNK. Your scanner beeps a tone. Then TRUNK and all of the bank numbers ﬂash.

2.Press the number key (1-9 and 0) of the desired target storage bank. Select one of the trunk systems by repeatedly pressing S or T to select a trunking system type, then press E/PGM.

Note: You can select from the following six systems:

Notes

You See	Trunk
	System

E2 – 800	Motorola
	Type II,
	800 MHz
	frequencies

53

Image 53

Radio Shack PRO-528 manual Programming trunked frequencies, You See Trunk System

Contents

PRO-528 1,000-Channel Handheld Trunking Scanner Contents Beyond the Basics Contents Basics Special features Contents Frequently asked questions Contents Basics Your scanner’s features HOLD/RESUME PGM Program programs frequencies into channels Alert turns Input a number or characters Volume turn the scanner on or off and adjust the volume Basics Supplying power to your scanner Battery cautions Connecting an earphone/ headphone Connecting the antenna Listening safely Attaching the belt clip About your scanner Basics Transferring data to or from another scanner or pc Understanding banks Service banks Channel storage banks Turning on the scanner and setting squelch Press SCAN/MANUAL Basics Storing known frequencies into channels Copying/moving a frequency Searching for and temporarily storing active frequencies Bank No Frequency Step kHz MHz Chain search Starting chain search Programming search ranges Storing found frequencies during chain search Direct search Service bank search Search skip memory Weather search Beyond the Basics Scanning the stored channels Manually selecting a channel Delay Special features Locking out channels Beyond the Basics Turning channel-storage banks on and off Priority MANUAL, HOLD/RESUME Using the keylock Wired programming Cloning your scanner Using the auto backlight display Using the display backlight Turning the keytone off/on Search speeds Skipping data signals Turning the battery save function off/on Receiving nwr-same and weather alert signals Turning on the digital weather alert feature Testing digital weather alert tone Programming a Fips code Programming Fips About Skywarn Skywarn Beyond the Basics Beyond the Basics Signal Stalker Setting the Signal Stalker I options Beyond the Basics PGM Trunking operation Using Signal Stalker Simultaneous trunking Beyond the Basics Setting the scanner to the trunking modeSetting squelch for the trunking mode You See Trunk System Programming trunked frequencies LTR Depending upon the trunk system selected Searching a trunked bank Beyond the Basics Turning a trunked bank on or off Turning the status bit ignore s-bit on or off Beyond the Basics Skipping a trunked bank Trunk Identifying a trunked frequency Edacs Ed talk group ID range search Locking out talk group IDs Using Hold to monitor an active talk group IDCLR /DELAY, 0, 1, then Srch Unlocking all talk group IDs Unlocking a single talk group ID Monitoring talk group IDs Using trunk scanning Scan Delay Manually storing talk group IDs in talk group ID lists Using talk group ID lists To enter a Type 1 ID Motorola talk groupsTo enter a Type 2 Talk Group ID Entering Edacs partial talk groups Beyond the Basics Edacs Ed talk groups You Press To Scan LTR talk groups Scanning the talk group ID lists All of them Priority talk group ID scanning Beyond the Basics Scanning type I and hybrid trunked systems Preset ﬂeet maps table E1P4 E1P5 E1P6 E1P13 E1P14 E1P15 Programming a ﬂeet map Beyond the Basics Selecting a preset ﬂeet map Beyond the Basics Programming the Base and Offset frequencies Programming a hybrid system Beyond the Basics Turning the Motorola disconnect tone detect function On/Off Transmitted or there is no signal at all My scanner is on but will not scan, why? Why won’t my scanner work at all? Why is ﬂashing? Beyond the Basics Why doesn’t my keypad work?Why am I getting poor or no reception? Why does Error appear? Why am I missing replies to conversations? Why isn’t my scanner acquiring a data channel?Why is the frequency used for the data channel missing? How do I reset my scanner? FCC notice Beyond the Basics Scanning legally Care Service and repair Sensitivity AM/FM SpeciﬁcationsFrequency Coverage Power Operating TemperatureSearch Speed Current Drain Beyond the Basics Beyond the Basics Beyond the Basics 06A06