108
Appendices
Troubleshooting
If the RD-700SX does not function in the way you expect, first check
the following points. If this does not resolve the problem, consult your
dealer or a nearby Roland Service Station.
* If certain messages appear in the display during operation, please refer
to
Error Messages/Other Messages
(p. 111).
Problem Check/Solution

Power Not

Coming On

Is the RD-700SX’s power cord properly
plugged into a power source as well as
connected to the RD-700SX?

No Sound

Is the power for connected amps and
speakers turned on? Is the volume turned
all the way down?
Is the VOLUME slider turned all the way
down?
Are all connections properly made?
• When using the RD-700SX as a stand-
alone instrument, be sure to connect
with audio cables or use headphones
(p. 21).
Are sounds audible with headphones
connected?
• If sounds are audible through
headphones, it may indicate that there
is a short in an audio cable or some sort
of amp or mixer problem. Check the
cables and equipment once again.
Is ZONE SWITCH set to OFF?
(p. 41, p. 64)
Is a Part’s volume turned off with the
ZONE LEVEL slider? (p. 41, p. 64)
If the sound for a pressed key does is not
being played, is the Local Switch set to
OFF?
• In the Utility Rec Setting in Edit mode,
set the Local Switch to ON (p. 101).
Are the effect settings correct?
Check following settings.
• ON/OFF settings for MULTI EFFECTS
[ON/OFF] (p. 52)
• Other Multi-Effect settings in Edit
mode (p. 87, p. 112)
Are the Wave Expansion Boards correctly
installed?
• When selecting settings while using the
EXPANSION [A] or [B] Tones or
Rhythm Sets, confirm that the specified
Wave Expansion Boards are properly
installed in the specified slots (p. 15).
Has the volume been lowered by pedal
operations or by MIDI messages (volume
messages or expression messages)
received from an external MIDI device?

No Sound for

Specific Part

Is the Part’s volume level turned down?
Check following settings.
• ZONE LEVEL sliders (p. 41, p. 64)
• Part Parameter Volume settings in Edit
mode (p. 92)
Are the Part’s MIDI Receive channel and
the MIDI Transmit channel for the
connected MIDI device matched?
Check the MIDI Receive channel settings
with Part Parameter Receive Channel in
Edit mode (p. 92).

No Sound From

the Connected

MIDI Device

Is the device enabled to transmit MIDI
messages?
• Set [EXTERNAL/INTERNAL] and
ZONE SWITCH to ON (p. 64). MIDI
messages cannot be transmitted if
ZONE SWITCH is set to OFF.
Is the RD-700SX’s keyboard controller
section MIDI Transmit channel matched
to the connected MIDI device’s MIDI
Receive channel?
• Make the Ch(MIDI Transmit Channel)
settings in the External screen (p. 62).

No Sound in a

Specific Range

Has the range in which sounds are to be
played (the key range) been set?
Check following settings.
• Settings for the LWR and UPR Parts in
the External screen (p. 66)
• Key Range settings in Zone Info (p. 69)
With certain Tones, for example Rhythm
Sets, bass Tones, Timpani, and other
Tones will not sound if a portion of the
Tone falls outside the recommended
range.
Is V-Link switched on (p. 97)?
• Set the Local ON/OFF to ON in the V-
Link Setting in Edit mode.
Sounds are played with keyboard even
when V-Link is switched on.

Tones Are

Altered

Did you call up a Setup?
• When a Setup is called up, the current
Tone, effect, and other settings are
disabled, and the selected Setup goes
into effect (p. 56). Resave required
settings to a Setup (p. 58).
Did you press ONE TOUCH [PIANO] or
[E.PIANO]?
• When ONE TOUCH [PIANO] or
[E.PIANO] is pressed, the current Tone,
effect, and other settings are disabled,
and settings for use in piano
performances go into effect (p. 32).
Resave required settings to a Setup (p.
58).
Problem Check/Solution
RD-700SX_e.book 108 ページ ２００６年３月２３日　木曜日　午後２時５２分