115
Effect/Parameter List
13: MULT PHASER (MULTI STAGE PHASER)
Extremely high settings of the phase difference produce a deep phaser
effect.
14: INF PHASER (INFINITE PHASER)
A phaser that continues raising/lowering the frequency at which the
sound is modulated.
15: RING MODLTR (RING MODULATOR)
This is an effect that applies amplitude modulation (AM) to the input
signal, producing bell-like sounds. You can also change the
modulation frequency in response to changes in the volume of the
sound sent into the effect.
16: STEP R.MOD (STEP RING MODULATOR)
This is a ring modulator that uses a 16-step sequence to vary the
frequency at which modulation is applied.
17: TREMOLO
Cyclically modulates the volume to add tremolo effect to the sound.
Step Rate Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
StepRate(Hz) 0.10–20.00
Hz
Rate of the step-wise change in the
phaser effect (Hz)
Step Rate
()
note (*1) Rate of the step-wise change in the
phaser effect (note)
Mix 0–127 Level of the phase-shifted sound
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level
Assignable Parameters
MFX Control Rate, Depth, Resonance, Manual, Mix
Parameter Value Description
Mode 4-STAGE,
8-STAGE,
12-STAGE,
16-STAGE,
20-STAGE,
24-STAGE
Number of phaser stages
Manual 0–127 Adjusts the basic frequency from which
the sound will be modulated.
Rate Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
Rate (Hz) 0.05–10.00
Hz
Frequency of modulation (Hz)
Rate ( ) note (*1) Frequency of modulation (note)
Depth 0–127 Depth of modulation
Resonance 0–127 Amount of feedback
Mix 0–127 Level of the phase-shifted sound
Pan L64–63R Stereo location of the output sound
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level
Assignable Parameters
MFX Control Speed, Resonance, Mix, Pan
Parameter Value Description
Mode 1, 2, 3, 4 Higher values will produce a deeper
phaser effect.
Speed -100– +100 Speed at which to raise or lower the
frequency at which the sound is
modulated
(+: upward / -: downward)
Resonance 0–127 Amount of feedback
Mix 0–127 Volume of the phase-shifted sound
Pan L64–63R Panning of the output sound
Low Gain -15– +15 dB Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB Amount of boost/cut for the high-
frequency range
Level 0–127 Output volume
Parameter Value Description
Assignable Parameters
MFX Control Frequency, Sens, Balance
Parameter Value Description
Frequency 0–127 Adjusts the frequency at which
modulation is applied.
Sens 0–127 Adjusts the amount of frequency
modulation applied.
Polarity UP, DOWN Determines whether the frequency
modulation moves towards higher
frequencies (UP) or lower frequencies
(DOWN).
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Level 0–127 Output level
Assignable Parameters
MFX Control Rate, Attack, Balance
Parameter Value Description
Step 01–16 0–127 Frequency of ring modulation at each
step
Rate Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
Rate (Hz) 0.05–10.00
Hz
Rate at which the 16-step sequence will
cycle (Hz)
Rate ( ) note (*1) Rate at which the 16-step sequence will
cycle (note)
Attack 0–127 Speed at which the modulation
frequency changes between steps
Low Gain -15– +15 dB Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB Amount of boost/cut for the high-
frequency range
Balance D100:0W–
D0:100W
Volume balance of the original sound
(D) and effect sound (W)
Level 0–127 Output volume
Assignable Parameters
MFX Control Rate, Depth, Mod Wave
Parameter Value Description
Mod Wave TRI, SQR,
SIN, SAW1,
SAW2
Modulation Wave
TRI
: Triangle wave
SQR
: Square wave
SIN
: Sine wave
SAW1/2
: Sawtooth wave
SAW1 SAW2
RD-700SX_e.book 115 ページ ２００６年３月２３日　木曜日　午後２時５２分