122
Effect/Parameter List
40: COMPRESSOR
Flattens out high levels and boosts low levels, smoothing out
fluctuations in volume.
41: LIMITER
Compresses signals that exceed a specified volume level, preventing
distortion from occurring.
42: GATE
Cuts the reverb’s delay according to the volume of the sound sent into
the effect. Use this when you want to create an artificial-sounding
decrease in the reverb’s decay.
43: DELAY
This is a stereo delay.
44: LONG DELAY
A delay that provides a long delay time.
BUILT-IN 1 open back enclosure 12 x 2 dynamic
BUILT-IN 2 open back enclosure 12 x 2 condenser
BUILT-IN 3 open back enclosure 12 x 2 condenser
BUILT-IN 4 open back enclosure 12 x 2 condenser
BUILT-IN 5 open back enclosure 12 x 2 condenser
BG STACK 1 sealed enclosure 12 x 2 condenser
BG STACK 2 large sealed enclosure 12 x 2 condenser
MS STACK 1 large sealed enclosure 12 x 4 condenser
MS STACK 2 large sealed enclosure 12 x 4 condenser
METAL
STACK
large double stack 12 x 4 condenser
2-STACK large double stack 12 x 4 condenser
3-STACK large triple stack 12 x 4 condenser
Assignable Parameters
MFX Control Threshold, Attack, Level
Parameter Value Description
Attack 0–127 Sets the speed at which compression
starts
Threshold 0–127 Adjusts the volume at which
compression begins
Post Gain 0– +18 dB Adjusts the output gain.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
Assignable Parameters
MFX Control Threshold, Release, Level
Parameter Value Description
Release 0–127 Adjusts the time after the signal volume
falls below the Threshold Level until
compression is no longer applied.
Threshold 0–127 Adjusts the volume at which
compression begins
Ratio 1.5:1, 2:1, 4:1,
100:1
Compression ratio
Post Gain 0– +18 dB Adjusts the output gain.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
Assignable Parameters
MFX Control Threshold, Hold, Release, Attack, Balance
Parameter Value Description
Threshold 0–127 Volume level at which the gate begins to
close
Type Cabinet Speaker Microphone
Mode GATE,
DUCK
Type of gate
GATE
: The gate will close when the
volume of the original sound
decreases, cutting the original sound.
DUCK (Ducking)
: The gate will close
when the volume of the original
sound increases, cutting the original
sound.
Attack 0–127 Adjusts the time it takes for the gate to
fully open after being triggered.
Hold 0–127 Adjusts the time it takes for the gate to
start closing after the source sound falls
beneath the Threshold.
Release 0–127 Adjusts the time it takes the gate to fully
close after the hold time.
Balance D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Level 0–127 Output level
Assignable Parameters
MFX Control Balance, Delay L, Delay R
Parameter Value Description
Delay L Mode ms, note When this is set to “note,” the effect is
synchronized with the tempo.
Delay L (ms) 1–1300 ms Adjusts the time until the delay sound is
heard. (Hz)
Delay L ( ) note (*1) Adjusts the time until the delay sound is
heard. (note)
Delay R Mode ms, note When this is set to “note,” the effect is
synchronized with the tempo.
Delay R (ms) 1–1300 ms Adjusts the time until the delay sound is
heard. (Hz)
Delay R ( ) note (*1) Adjusts the time until the delay sound is
heard. (note)
Phase Left NORMAL,
INVERSE
Phase of the delay sound
Phase Right
Feedback Mode NORMAL,
CROSS
Selects the way in which delay sound is
fed back into the effect. (See the figures
above.)
Feedback -98– +98 % Adjusts the amount of the delay sound
that’s fed back into the effect. Negative
(-) settings invert the phase.
HF Damp 200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don’t want to filter out any
high frequencies, set this parameter to
BYPASS.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output level
Assignable Parameters
MFX Control Balance, Delay, Pan
Parameter Value Description
Delay Mode ms, note When this is set to “note,” the effect is
synchronized with the tempo.
Delay (ms) 1–2600 ms Delay time from when the original
sound is heard to when the delay sound
is heard (Hz)
Parameter Value Description
RD-700SX_e.book 122 ページ 2006年3月23日 木曜日 午後2時52分