134
Effect/Parameter List
87: *OVERDRIVE
This effect creates a soft distortion similar to that produced by vacuum
tube amplifiers.
88: *DISTORTION
This effect produces a more intense distortion than Overdrive.
89: *PHASER
A phaser adds a phase-shifted sound to the direct sound, producing a
twisting modulation that creates spaciousness and depth.
90: *SPECTRUM
Spectrum is a type of filter which modifies the timbre by boosting or
cutting the level at specific frequencies. It is similar to an equalizer, but
has 8 frequency points fixed at locations most suitable for adding
character to the sound.
91: *ENHANCER
The Enhancer controls the overtone structure of the high frequencies,
adding sparkle and tightness to the sound.
P2 Q 0.5, 1.0, 2.0,
4.0, 8.0
This parameter adjusts the width of the
area around the Middle 2 Frequency
that will be affected by the Gain setting.
Higher values of Middle 2 Q will result
in a narrower area being affected.
P2 Gain -15– +15 dB Adjust the gain for the area specified by
the Middle 2 Frequency and Q settings.
Positive (+) settings will emphasize
(boost) the Middle 2 range.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Drive, Amp Type, Pan
Parameter Value Description
Drive 0–127 Adjust the degree of distortion. The
volume will change together with the
degree of distortion.
Pan L64–0–63R Adjust the stereo location of the output
sound. L64 is far left, 0 is center, and 63R
is far right.
Amp Type SMALL,
BUILT-IN,
2-STACK,
3-STACK
Select the type of guitar amp.
SMALL
: small amp
BUILT-IN
: single-unit type amp
2-STACK
: large double stack amp
3-STACK
: large triple stack amp
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Level 0–127 Adjust the output level.
It’s a good idea to use this Parameter to
adjust the difference in volume between
when Overdrive is applied and when it
is not applied.
Assignable Parameters
MFX Control Drive, Amp Type, Pan
Parameter Value Description
Drive 0–127 Adjust the degree of distortion. The
volume will change together with the
degree of distortion.
Pan L64–0–63R Adjust the stereo location of the output
sound. L64 is far left, 0 is center, and 63R
is far right.
Amp Type SMALL,
BUILT-IN,
2-STACK,
3-STACK
Select the type of guitar amp.
SMALL
: small amp
BUILT-IN
: single-unit type amp
2-STACK
: large double stack amp
3-STACK
: large triple stack amp
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Parameter Value Description
Level 0–127 Adjust the output level.
It’s a good idea to use this parameter to
adjust the difference in volume between
when Distortion is applied and when it
is not applied.
Assignable Parameters
MFX Control Rate, Depth, Manual
Parameter Value Description
Manual 100–8000 Hz Adjust the basic frequency from which
the sound will be modulated.
Rate 0.05–10.00
Hz
Adjust the frequency (period) of
modulation.
Depth 0–127 Adjust the depth of modulation.
Resonance 0–127 Adjust the amount of feedback for the
phaser.
The effect becomes more prominent as
the value is increased.
Mix 0–127 Adjust the ratio with which the phase-
shifted sound is combined with the
direct sound.
Pan L64–0–63R Adjust the stereo location of the output
sound. L64 is far left, 0 is center, and 63R
is far right.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Pan, Level
Parameter Value Description
Band1 (250Hz) -15– +15 dB Adjust the 250 Hz gain.
Band2 (500Hz) -15– +15 dB Adjust the 500 Hz gain.
Band3 (1000Hz) -15– +15 dB Adjust the 1000 Hz gain.
Band4 (1250Hz) -15– +15 dB Adjust the 1250 Hz gain.
Band5 (2000Hz) -15– +15 dB Adjust the 2000 Hz gain.
Band6 (3150Hz) -15– +15 dB Adjust the 3150 Hz gain.
Band7 (4000Hz) -15– +15 dB Adjust the 4000 Hz gain.
Band8 (8000Hz) -15– +15 dB Adjust the 8000 Hz gain.
Q 0.5, 1.0, 2.0,
4.0, 8.0
Simultaneously adjust the width of the
adjusted areas for all the frequency
bands.
Pan L64–0–63R Adjust the stereo location of the output
sound. L64 is far left, 0 is center, and 63R
is far right.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Sens, Mix
Parameter Value Description
Sens 0–127 Adjust the sensitivity of the enhancer.
Parameter Value Description
RD-700SX_e.book 134 ページ ２００６年３月２３日　木曜日　午後２時５２分