Roland XP-30 owner manual OVERDRIVE→ Flanger, OVERDRIVE→ Delay, DISTORTION→ Chorus, 104

Chapter 3. Creating Your Own Sounds

ChoRate (Chorus Rate)

Adjust the modulation speed of the chorus effect.

Chorus Depth

Adjust the modulation depth of the chorus effect.

Chorus Balance #

Adjust the volume balance between the overdrive sound that is sent through the chorus and the overdrive sound that is not sent through the chorus. With a setting of “D100: 0W,” only the overdrive sound will be output. With a setting of “D0: 100W,” only the overdrive sound that is sent through the chorus will be output.

Level (Output Level)

Adjust the output level.

27: OVERDRIVE→ FLANGER

This effect connects an overdrive and a flanger in series.

Balance D

28: OVERDRIVE→ DELAY

This effect connects an overdrive and a delay in series.

L in	L out
	Balance D
	Balance W
Overdrive	Delay
	Balance W
	Feedback
R in	R out
	Balance D

OD Drive

Adjust the degree of overdrive distortion. The volume will change together with the degree of distortion.

OD Pan (Overdrive Pan) #

Adjust the stereo location of the overdrive sound. L64 is far left, 0 is center, and 63R is far right.

DlyTime (Delay Time)

Adjust the time delay from when the direct sound begins until the delay sound is heard.

L in

Feedback

L out

Balance W

Dly Fbk (Delay Feedback Level)

Overdrive

R in

Flanger

Balance W

R out

Balance D

Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

Delay HF Damp

OD Drive

Adjust the degree of overdrive distortion. The volume will change together with the degree of distortion.

OD Pan (Overdrive Pan) #

Adjust the stereo location of the overdrive sound. L64 is far left, 0 is center, and 63R is far right.

Flg Dly (Flanger Pre Delay Time)

Adjust the time delay from when the direct sound begins until the flanger sound is heard.

FlgRate (Flanger Rate)

Adjust the modulation speed of the flanger effect.

Flg Dpt (Flanger Depth)

Adjust the modulation depth of the flanger effect.

Flg Fbk (Flanger Feedback Level)

Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

Flanger Balance #

Adjust the volume balance between the overdrive sound that is sent through the flanger and the overdrive sound that is not sent through the flanger. With a setting of “D100: 0W,” only the overdrive sound will be output. With a setting of “D0: 100W,” only the overdrive sound that is sent through the flanger will be output.

Level (Output Level)

Adjust the output level.

Adjust the frequency above which delayed sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

Delay Balance (Delay Balance) #

Adjust the volume balance between the overdrive sound that is sent through the delay and the overdrive sound that is not sent through the delay. With a setting of “D100: 0W,” only the overdrive sound will be output. With a setting of “D0: 100W,” only the overdrive sound that is sent through the delay will be output.

Level (Output Level)

Adjust the output level.

29: DISTORTION→ CHORUS

This effect connects distortion and chorus in series. The parameters are essentially the same as “26: OVERDRIVE→ CHORUS,” with the exception of the following two.

OD Drive → Dist Drive (Specify the amount of distortion.) OD Pan → Dist Pan (Specify the stereo location of the

distortion sound.)

L in	L out
	Balance D
	Balance W
Distortion	Chorus
	Balance W
R in	R out
	Balance D

104