Roland XP-30 owner manual 186

MIDI Implementation

●All Note Off (Controller number 123)

status	2nd byte	3rd byte
BnH	7BH	00H
n=MIDI channel number:		0H - FH (ch.1 - ch.16)

*When All Note Off is received, all currently sounding notes of the corresponding channel will be turned off. However if Hold 1 or Sostenuto are on, the sound will be held until these are turned off.

*Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

●Omni Off (Controller number 124)

status	2nd byte	3rd byte
BnH	7CH	00H
n=MIDI channel number:		0H - FH (ch.1 - ch.16)

*The same processing as when All Note Off is received will be done.

*Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

●Omni On (Controller number 125)

status	2nd byte	3rd byte
BnH	7DH	00H
n=MIDI channel number:		0H - FH (ch.1 - ch.16)

*The same processing as when All Note Off is received will be done. The instrument will not be set to OMNI ON.

*Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

●Mono (Controller number 126)

status	2nd byte	3rd byte
BnH	7EH	mmH
n=MIDI channel number:		0H - FH (ch.1 - ch.16)
mm=Mono number:		00H - 10H (0 - 16)

*The same processing as when All Note Off is received will be done, and the Assign parameter (PATCH/CONTROL/KEY MODE & BENDER) will be set to SOLO.

*Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

●Poly (Controller number 127)

status	2nd byte	3rd byte
BnH	7FH	00H

n=MIDI channel number:0H - FH (ch.1 - ch.16)

*The same processing as when All Note Off is received will be done, and the Assign parameter (PATCH/CONTROL/KEY MODE & BENDER) will be set to POLY.

*Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

■System Realtime Messages

●Timing Clock

status F8H

*This message will be received if the Clock Source parameter (SYSTEM/SETUP/SYSTEM SETUP) is MIDI (p. 129).

●Active Sensing

status

FEH

*When an Active Sensing message is received, the unit will begin monitoring the interval at which MIDI messages are received. During monitoring, if more than 420 ms passes without a message being received, the same processing will be done as when All Sound Off, All Note Off, and Reset All Controllers messages are received. Then monitoring will be halted.

■System Exclusive Messages

status	data byte	status
F0H	iiH, ddH, ......, eeH	F7H
F0H:	System Exclusive message status
ii = ID number:	This is the ID number (manufacturer ID) that specifies the
	manufacturer whose exclusive message this is. Roland's manufacturer
	ID is 41H.ID numbers 7EH and 7FH are defined in an expansion of the
	MIDI standard as Universal Non-realtime messages (7EH) and
	Universal Realtime Messages (7FH).
dd,..., ee = data:	00H - 7FH (0 - 127)
F7H:	EOX (End Of Exclusive)

Of the System Exclusive messages received by this device, the Universal Non-realtime messages and the Universal Realtime messages and the Data Request (RQ1) messages and the Data Set (DT1) messages will be set automatically.

●Universal Non-realtime System Exclusive Messages

❍Identity Request Message

When this message is received, Identity Reply message (p. 189) will be transmitted.

status	data byte	status
F0H	7EH, dev, 06H, 01H	F7H
Byte	Remarks
F0H	Exclusive status
7EH	ID number	(Universal Non-realtime message)
dev	device ID	(dev: 10H - 1FH)
06H	sub ID#1	(General Information)
01H	sub ID#2	(Identity Request)
F7H	EOX	(End Of Exclusive)

*The “dev” is own device number or 7FH (Broadcast).

❍GM System On

“GM System On” is a command message that resets the internal settings of the instrument to the GM initial state (General MIDI System - Level 1). A GM instrument that receives this message will automatically enter a state in which it can correctly perform a GM score.

status	data byte	status
F0H	7EH, 7FH, 09H, 01H F7H
Byte	Remarks
F0H	Exclusive status
7EH	ID number	(Universal Non-realtime message)
7FH	device ID	(Broadcast)
09H	sub ID#1	(General MIDI Message)
01H	sub ID#2	(General MIDI On)
F7H	EOX	(End Of Exclusive)

*Not received when the Rx.GM parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF.

❍GM System Off

When this messages is received, this instrument will return to the performance mode.

status	data byte	status
F0H	7EH, 7FH, 09H, 02H F7H
Byte	Remarks
F0H	Exclusive status
7EH	ID number	(Universal Non-realtime message)
7FH	device ID	(Broadcast)
09H	sub ID#1	(General MIDI Message)
02H	sub ID#2	(General MIDI Off)
F7H	EOX	(End Of Exclusive)

*Not received when the Rx.GM parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF.

186