Roland XP-30 owner manual 185

❍Effect 1 (Reverb Send Level) (Controller number 91)

status	2nd byte	3rd byte
BnH	5BH	vvH
n=MIDI channel number:		0H - FH (ch.1 - ch.16)
vv=Reverb Send Level:		00H - 7FH (0 - 127)

*In Performance mode, the Reverb Send Level parameter of each Part will change.

❍Effect 3 (Chorus Send Level) (Controller number 93)

status	2nd byte	3rd byte
BnH	5DH	vvH
n=MIDI channel number:		0H - FH (ch.1 - ch.16)
vv=Chorus Send Level:		00H - 7FH (0 - 127)

*In Performance mode, the Chorus Send Level parameter of each Part will change.

❍RPN MSB/LSB (Controller number 100, 101)

status	2nd byte	3rd byte
BnH	65H	mmH
BnH	64H	llH

n=MIDI channel number: 0H - FH (ch.1 - ch.16)

mm=MSB of the parameter number specified by RPN ll=LSB of the parameter number specified by RPN

<<< RPN >>>

Control Changes include RPN (Registered Parameter Numbers), which are extended parameters whose function is defined in the MIDI specification.

When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any order) is transmitted to specify the parameter you wish to control. Then, Data Entry messages (Controller numbers 6 and 38) are used to set the value of the specified parameter. Once a RPN parameter has been specified, all further Data Entry messages on that channel are considered to apply to that specified parameter. In order to prevent accidents, when the desired setting has been made for the parameter, it is recommended that RPN be set to Null.

This device receives the following RPNs.

RPN	Data entry
MSB LSB	MSB LSB	Notes
00H 00H	mmH -	Pitch Bend Sensitivity
		mm : 00H - 0CH (0 - 12 semitones)
		ll : ignored (processed as 00H)
		Up to 1 octave can be specified in semitone steps.
		*The Bend Range parameter (PATCH/
		CONTROL/KEY MODE & BENDER) will
		also be changed.
		*Not received by the Rhythm Part (Part 10).
00H 01H	mmH llH	Channel Fine Tuning
		mm, ll : 20 00H - 40 00H - 60 00H
		( -4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent )
		*In Patch mode, the Master parameter
		(SYSTEM/TUNE/TUNE) will change.
		*In Performance mode, the Fine parameter
		(PERFORM/PART/SETTING) of each Part
		will change. When received on the Control
		channel, the Master parameter (SYSTEM/
		TUNE/TUNE) will change.
00H 02H	mmH -	Channel Coarse Tuning
		mm : 10H - 40H - 70H (-48 - 0 - +48 semitones)
		ll : ignored (processed as 00H)
		*Not received in Patch mode.
		*In Performance mode, the Coarse parameter
		(PERFORM/PART/SETTING) of each Part
		will change.
7FH 7FH	- -	RPN null
		RPN and NRPN will be set as “unspecified.”
		Once this setting has been made, subsequent
		Data Entry messages will be ignored. (It is not
		necessary to transmit Data Entry for RPN Null
		settings.
		Parameter values that were previously set will
		not change.
		mm, ll: ignored

MIDI Implementation

●Program Change

status	2nd byte
CnH	ppH
n=MIDI channel number:		0H - FH (ch.1 - ch.16)
pp=Program number:		00H - 7FH (prog.1 - prog.128)

*Not received when the Program Change parameter (SYSTEM/MIDI/RECEIVE MIDI) is OFF.

*When received on the Control channel, the Performance will change.

*Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

●Channel Aftertouch

status	2nd byte
DnH	vvH
n=MIDI channel number:		0H - FH (ch.1 - ch.16)
vv=Channel Aftertouch:		00H - 7FH (0 - 127)

*Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

●Pitch Bend Change

status	2nd byte	3rd byte
EnH	llH	mmH
n=MIDI channel number:		0H - FH (ch.1 - ch.16)
mm,ll=Pitch Bend value:		00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

*Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

■Channel Mode Messages

●All Sound Off (Controller number 120)

status	2nd byte	3rd byte
BnH	78H	00H
n=MIDI channel:		0H - FH (ch.1 - ch.16)

*When this message is received, all notes currently sounding on the corresponding channel will be turned off.

*Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

●Reset All Controllers (Controller number 121)

status	2nd byte	3rd byte
BnH	79H	00H
n=MIDI channel number:		0H - FH (ch.1 - ch.16)

*Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

*When this message is received, the following controllers will be set to their reset values.

Controller	Reset value
Pitch Bend Change	[+-]0 (center)
Polyphonic Key Pressure	0	(off)
Channel Pressure	0	(off)
Modulation	0	(off)
Breath type	0	(minimum)
Expression	127 (maximum)
	However the controller will be at minimum.
Hold 1	0	(off)
Sostenuto	0	(off)	Appendices
Soft	0	(off)
Hold 2	0	(off)
RPN	Unset. Previously set data will not change.
NRPN	Unset. Previously set data will not change.
System General purpose controller 10	(minimum)
System General purpose controller 20	(minimum)

185