N(NORTH), NE(NORTH-

SET ZOOM

Press [ENTER] at the “SET ZOOM...” position to enter the ZOOM setup screen. After ZOOM setup, the PRIVACY ZONE function will be in action only at the higher magnification than the Zoom magnification

as set.

 

PRIVACY ZONE SET

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SET ZOOM

 

 

 

 

 

 

 

 

 

 

 

SET ZONE AREA

ON...

 

 

 

 

 

 

SET ZOOM

 

...

 

 

 

 

 

REVERSE

OFF

 

 

 

 

 

 

 

 

Press

 

 

 

 

 

 

 

 

[Enter]

 

 

 

 

 

EXIT

QUIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REVERSE

The REVERSE function applies PRIVACY MASK to the other area than set as a privacy zone. ON/OFF is available.

PRIVACY ZONE SET 0

SET ZONE AREA

ON...

SET ZOOM

...

REVERSE

 

ON

EXIT

QUIT

EXIT

"QUIT" : Does not save the selected information and returns to a higher menu.

"SAVE" : Do saves the selected information and returns to a higher menu.

"DEL" : Deletes the selected information and restores the DEFAULT. Then returns to a higher menu.

ZONE DIR SET/ZONE AREA SET

This function indicates the ID or direction depending on the set value when PAN of SCC-C6475(P) is located in a specific area. If set to AREA, it indicates the ID of the selected area and if set to

EAST), E(EAST), SE(SOUTH-EAST), S(SOUTH), SW(SOUTH-WEST), W(WEST), NW(NORTH-WEST.

ZONE DIR SET

Press the [Enter] key in the “ZONE DIR SET ON…” mode to enter the NORTH SET screen. MAP. Move PAN to set the NORTH position and press [ENTER]. Based on the North position,the direction of N(North), NE(North-East), E(East), SE(South-East), S(South), SW(South-West), W(West), NW(North-West) is displayed whenever you move PAN.

Caution ZONE DIR/AREA OSD is not displayed in the network viewer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(ZONE SET)

 

 

 

 

 

 

 

 

E

 

 

 

SET NORTH

 

 

 

 

 

 

 

 

 

 

 

 

PRIVACY ZONE ...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZONE DIR SET

 

ON...

 

 

 

 

 

 

 

 

ZONE AREA SET

OFF

 

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

 

Press

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[Enter]

 

 

 

 

 

 

 

 

EXIT

QUIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZONE AREA

Press [ENTER] to enter the ZONE AREA MAP screen from “ZONE

AREA SET...”. Select a ZONE AREA number from the ZONE AREA MAP

screen and press [ENTER] to enter the ZONE AREA setup screen.

(ZONE SET)

 

 

(ZONE AREA MAP)

 

 

 

 

 

PRIVACY ZONE

...

 

 

 

 

 

 

 

0

*

1

2

3

ZONE DIR SET

OFF

4

5

6

7

ZONE AREA SET

ON...

 

Press [Enter]

EXITQUIT

RET

 

ZONE AREA SET

0

 

 

 

 

 

 

...

 

LOCATION

 

ZONE ID SET

...

 

Press

ZONE ENABLE

ON

 

 

 

 

 

[Enter]

 

 

 

 

 

EXIT

QUIT

 

 

 

 

 

 

 

 

 

 

 

4-20

4-21