To delete all registered IDs, ALL ID Clear

TO CHECK THE NUMBER OF REGISTERED IDs

You can check the total number of registered IDs.

1.Press the F7 SETUP MENU button.

2. Use the buttons	4 and	6 to move to the REG. ID COUNT item and	5. REG. ID COUNT
press ENT .			5. REG. ID COUNT
press ENT .
			00123

3.The number of registered IDs will be shown on the screen.

M The number of registered IDs will be displayed in 5 digits.

TO REMOVE ALL REGISTERED IDs

You can remove all of the registered user IDs.

1. Press the F8 SETUP MENU button.

USER MANAGEMENT

2.	Use the buttons	4	and 6 to move to the ALL ID CLEAR item and
	press ENT .
3.	Press the button	1	to delete all registered IDs.

• To cancel the work, press the button 0 .

3. ALL ID CLEAR

3.ALL ID CLEAR 1:YES, 0:NO

J Please upload the ID data to the host PC before deletion, just for backup purposes.

English _ 35

Page 35

Image 35

Samsung SSA-S2100/EXP manual To delete all registered IDs, To cancel the work, press the button, ALL ID Clear

Contents

Please visit our website Standalone Rfid Access Controller Safety information Safety information This device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Default Settings Event Memory SetupVoice Volume Setup Input Type Setup Product introduction Features Duress Alarm External I/O PinsForced Door Open Alarm Door Open Timeout Alarm Quick Guide CD Manual WHAT’S Included LCD AT a GlanceFront Panel LED Communication status indicatorPin Connector Preliminary connector for extension Rear Panel Cable Color Scheme PIN ConnectorPins Signal Cable Color Cable Selection TCP/IP RJ45 Connector Follow the instructions below to install the wall mount Installing the Wall Mount Bypass Diode Connection Connecting the Termination Resistor and Diode Host PC EARTH-GROUNDING the Communication Cables Input Connection Connection Output Connection External Reader Connection External Reader Connection RS-232 Communication Port Connection Communication Line Connection Please follow the steps below RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Max m Connect all RS-485 ports of the product in parallel TCP/IP Communication Port Connection Initializing the System Initializing the system using the Initialize switchSystem Initialization in Master Mode Initialization To register a master card To Access the Master ModeRegistering a Master ID 00/00 Name DisplayTo register a master card PIN € English € Espanol € Portuguese User Count SetupLanguage Setup MAX User Setup Comm Addr SET DATE/TIME SetupCommunication Address Setup SET DATE/TIME Baud Rate Baud Rate SetupFactory Defaults Default SET Reader #2 Mode Reader mode setupReader #1 Mode RD#1 KEY Input not USE € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY Input To register ID Registering ID in Quick ModeQuick Mode Registration User management PW TA TB C RD MA MB LV ID Registered Registering the IDTo register the ID card SCANNING… PW TA TB C RD MA MB LV ID Registered User Management To register the PIN numberTo select PIN SSA-S2101 Numeric letters in 4 ~ 8 or 10 digits ID List To Delete IDViewing the ID List ALL ID Clear To cancel the work, press the buttonTo delete all registered IDs Master ID CLR Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W To delete all registered master IDs ARM/DISARM SET Door Open Alarm Time SetupARM/DISARM Open ALR Time User Management To select USE or not USE, and press ENT . J not USE TWO MEN Operation ModeTo move to the TWO MEN Mode item To Check the Number of Events To Remove the Time Schedule To Remove ALL Events Exit Button Time setupDoor Contact Sensor Setup Exit Button Output AUX INPUT#1 Auxiliary Input #1 SetupAuxiliary Input #2 Setup Time Setup CUT OFF Alarm Tamper Alarm Output SetupCUT OFF Output Setup Tamper Alarm ARM/DISARM Output Setup Duress Mode Output Setup Output Setup for Level IDs Accessing Reader #1 Door Open Timeout Setup Output Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 Antipassback Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Time Schedule Error Output Setup RD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2 12.RD2 ID Error Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 Reader #2 ID Error Output Setup 14.RD2 APB Error Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 13.RD2 T/S Error Time Setup Time Unit Unit 1SEC Unit 0.1SEC Advanced setupTime Unit Setup Output Time SCHEDULE+ID Use the 4 Buttons to specify the interval, day Antipassback ModeTime Schedule Setup APB Mode Not USE ALL Clear Holiday Setup Code 10 Holiday Code SetupHoliday Code Code 01 RD2 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD1 Mode I T/S T/S Code ‘00’ means no Time Schedules are to be applied Output Time Schedule SetupVoice Message Time Schedule Voice I T/S CUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Wiegand Output not USE Not USE Wiegand Output SetupVoice Volume Setup Voice Volume Version Check  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features ONE Time Read Output Test Input Test Press ANY KEY Last UpdateLCD Test Keypad Test Reader Test SCANNING… RAM TESTING…Reader Test Memory Test Comm Test Communication Test O , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Menu Structure Other information F4 button Menu Structure of the F3 buttonF3 button Menu Structure of the F4 button Other Information Menu Structure of the F5 buttonF5 button F6 button Menu Structure of the F6 button Menu Structure of the F8 button Menu Structure of the F7 button F12 button Menu Structure of the F9 buttonF9 button Menu Structure of the F12 button TTL#1 TTL#2 Default SettingsOutput Settings for Input Sources Duress Alarm Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Controller and the Host PC fails CardBuzzer keeps beeping Communication between Product speciﬁcations Product Specifications Correct disposal of batteries in this product

TO CHECK THE NUMBER OF REGISTERED IDs

TO REMOVE ALL REGISTERED IDs

to delete all registered IDs.

• To cancel the work, press the button 0 .

3. ALL ID CLEAR