To Remove ALL Events | Samsung SSA-S2100/EXP guide

TO REMOVE ALL EVENTS

If the event memory is full or you want to change the number of IDs, you can use this menu to clear the event memory.

1.Press the F8 SETUP MENU button.

2.	Use the buttons	4	and 6 to move to the EVENT CLEAR item and
	press ENT .
3.	Press the button	1	to remove all events.

•To cancel the work, press the button 0.

J To reserve the events, upload them to the host PC before deletion.

TO REMOVE THE TIME SCHEDULE

2.EVENT CLEAR

1:YES, 0:NO

DELETE ALL EVENT

WAIT…

USER MANAGEMENT

All time schedules (01~10), all holiday schedules (01~10), holiday codes, and time schedules for reader#1 and reader#2 modes can be deleted. With the ENT button pressed, press the 1 button to remove all time schedules or press the

0button to cancel the work.

1.Press the F8 SETUP MENU button.

2.	Use the buttons	4	and 6 to move to the T/S CLEAR item and	5.T/S CLEAR
	press ENT .
3.	Press the button	1	to remove all time schedules.	1:YES, 0:NO

• To cancel the work, press the button 0 .

•You will see the message as shown at the right.

DELETE TS

WAIT…

J Before removing all time schedules, ensure that they are no longer in use.

English _ 39

Image 39

Samsung SSA-S2100/EXP manual To Remove ALL Events, To Remove the Time Schedule

Contents

Please visit our website Standalone Rfid Access Controller Safety information Safety information Important Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Default Settings Event Memory SetupVoice Volume Setup Input Type Setup Product introduction Features Duress Alarm External I/O PinsForced Door Open Alarm Door Open Timeout Alarm Quick Guide CD Manual WHAT’S Included AT a Glance Front PanelLCD LED Communication status indicatorPin Connector Preliminary connector for extension Rear Panel PIN Connector Pins Signal Cable ColorCable Color Scheme Cable Selection TCP/IP RJ45 Connector Follow the instructions below to install the wall mount Installing the Wall Mount Bypass Diode Connection Connecting the Termination Resistor and Diode Host PC EARTH-GROUNDING the Communication Cables Input Connection Connection Output Connection External Reader Connection External Reader Connection RS-232 Communication Port Connection Communication Line Connection Please follow the steps below RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Max m Connect all RS-485 ports of the product in parallel TCP/IP Communication Port Connection Initializing the System Initializing the system using the Initialize switchSystem Initialization in Master Mode Initialization To Access the Master Mode Registering a Master IDTo register a master card Name Display To register a master card PIN00/00 € English € Espanol € Portuguese User Count SetupLanguage Setup MAX User Setup Comm Addr SET DATE/TIME SetupCommunication Address Setup SET DATE/TIME Baud Rate Baud Rate SetupFactory Defaults Default SET Reader mode setup Reader #1 ModeReader #2 Mode RD#1 KEY Input not USE € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY Input To register ID Registering ID in Quick ModeQuick Mode Registration User management PW TA TB C RD MA MB LV ID Registered Registering the IDTo register the ID card SCANNING… PW TA TB C RD MA MB LV ID Registered User Management To register the PIN numberTo select PIN SSA-S2101 Numeric letters in 4 ~ 8 or 10 digits To Delete ID Viewing the ID ListID List To cancel the work, press the button To delete all registered IDsALL ID Clear Master ID CLR Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W To delete all registered master IDs ARM/DISARM SET Door Open Alarm Time SetupARM/DISARM Open ALR Time User Management To select USE or not USE, and press ENT . J not USE TWO MEN Operation ModeTo move to the TWO MEN Mode item To Check the Number of Events To Remove the Time Schedule To Remove ALL Events Exit Button Time setupDoor Contact Sensor Setup Exit Button Output AUX INPUT#1 Auxiliary Input #1 SetupAuxiliary Input #2 Setup Time Setup CUT OFF Alarm Tamper Alarm Output SetupCUT OFF Output Setup Tamper Alarm ARM/DISARM Output Setup Duress Mode Output Setup Output Setup for Level IDs Accessing Reader #1 Door Open Timeout Setup Output Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Antipassback Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Time Schedule Error Output Setup RD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2 12.RD2 ID Error Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 Reader #2 ID Error Output Setup 14.RD2 APB Error Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 13.RD2 T/S Error Time Setup Time Unit Unit 1SEC Unit 0.1SEC Advanced setupTime Unit Setup Output Time SCHEDULE+ID Use the 4 Buttons to specify the interval, day Antipassback ModeTime Schedule Setup APB Mode Not USE ALL Clear Holiday Setup Code 10 Holiday Code SetupHoliday Code Code 01 RD2 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD1 Mode I T/S T/S Code ‘00’ means no Time Schedules are to be applied Output Time Schedule SetupVoice Message Time Schedule Voice I T/S Input Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Wiegand Output not USE Not USE Wiegand Output SetupVoice Volume Setup Voice Volume Version Check  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features ONE Time Read Output Test Input Test Press ANY KEY Last UpdateLCD Test Keypad Test Reader Test SCANNING… RAM TESTING…Reader Test Memory Test Comm Test Communication Test Input Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other information F4 button Menu Structure of the F3 buttonF3 button Menu Structure of the F4 button Menu Structure of the F5 button F5 buttonOther Information F6 button Menu Structure of the F6 button Menu Structure of the F8 button Menu Structure of the F7 button F12 button Menu Structure of the F9 buttonF9 button Menu Structure of the F12 button TTL#1 TTL#2 Default SettingsOutput Settings for Input Sources Duress Alarm Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Controller and the Host PC fails CardBuzzer keeps beeping Communication between Product speciﬁcations Product Specifications Correct disposal of batteries in this product