Menu Structure of the F9 button, F12 button

other information

Menu Structure of the [F9] button

You can check the system version. You can also test the input, output, LCD, keypad, reader, memory and communication status.

F9 button

FIRMWARE VER

INPUT TEST

OUTPUT TEST

LCD TEST

KEYPAD TEST

READER TEST

MEMORY TEST

COMM TEST

Menu Structure of the [F12] button

You can easily register or delete IDs without going through a complex setup procedure.

F12 button

(QUICK MODE) REGISTRATION

(QUICK MODE) ID DELETE

70_ other information

Page 70

Image 70

Samsung SSA-S2100/EXP manual Menu Structure of the F9 button, Menu Structure of the F12 button

Contents

Standalone Rfid Access Controller Please visit our website Safety information Safety information Safety Information Important Safety InstructionsThis device may not cause harmful interference, Contents Contents Input Type Setup Event Memory SetupVoice Volume Setup Default Settings Features Product introduction Door Open Timeout Alarm External I/O PinsForced Door Open Alarm Duress Alarm WHAT’S Included Quick Guide CD Manual Front Panel AT a GlanceLCD Rear Panel Communication status indicatorPin Connector Preliminary connector for extension LED Pins Signal Cable Color PIN ConnectorCable Color Scheme TCP/IP RJ45 Connector Cable Selection Installing the Wall Mount Follow the instructions below to install the wall mount Connecting the Termination Resistor and Diode Bypass Diode Connection EARTH-GROUNDING the Communication Cables Host PC Connection Input Connection Output Connection External Reader Connection External Reader Connection Communication Line Connection RS-232 Communication Port Connection Max m RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Please follow the steps below TCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallel Initialization Initializing the system using the Initialize switchSystem Initialization in Master Mode Initializing the System Registering a Master ID To Access the Master ModeTo register a master card To register a master card PIN Name Display00/00 MAX User Setup User Count SetupLanguage Setup € English € Espanol € Portuguese SET DATE/TIME DATE/TIME SetupCommunication Address Setup Comm Addr SET Default SET Baud Rate SetupFactory Defaults Baud Rate Reader #1 Mode Reader mode setupReader #2 Mode Reader #2 KEY Input € USE If set, you can get access using the keypad inputReader #1 KEY Input RD#1 KEY Input not USE User management Registering ID in Quick ModeQuick Mode Registration To register ID SCANNING… Registering the IDTo register the ID card PW TA TB C RD MA MB LV ID Registered SSA-S2101 Numeric letters in 4 ~ 8 or 10 digits To register the PIN numberTo select PIN PW TA TB C RD MA MB LV ID Registered User Management Viewing the ID List To Delete IDID List To delete all registered IDs To cancel the work, press the buttonALL ID Clear To delete all registered master IDs Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W Master ID CLR Open ALR Time User Management Door Open Alarm Time SetupARM/DISARM ARM/DISARM SET To Check the Number of Events TWO MEN Operation ModeTo move to the TWO MEN Mode item To select USE or not USE, and press ENT . J not USE To Remove ALL Events To Remove the Time Schedule Exit Button Output Time setupDoor Contact Sensor Setup Exit Button Time Setup Auxiliary Input #1 SetupAuxiliary Input #2 Setup AUX INPUT#1 Tamper Alarm Tamper Alarm Output SetupCUT OFF Output Setup CUT OFF Alarm Duress Mode Output Setup ARM/DISARM Output Setup Door Open Timeout Setup Output Setup for Level IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Time Schedule Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Antipassback Error Output Setup Output Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2 Reader #2 ID Error Output Setup Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 12.RD2 ID Error 13.RD2 T/S Error Time Setup Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 14.RD2 APB Error Output Time SCHEDULE+ID Advanced setupTime Unit Setup Time Unit Unit 1SEC Unit 0.1SEC APB Mode Not USE ALL Clear Antipassback ModeTime Schedule Setup Use the 4 Buttons to specify the interval, day Holiday Setup Code 01 Holiday Code SetupHoliday Code Code 10 RD1 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD2 Mode I T/S Voice I T/S Output Time Schedule SetupVoice Message Time Schedule T/S Code ‘00’ means no Time Schedules are to be applied Input CUT OFF Check Setup Input Time Schedule SetupCUT OFF SET Event Memory Setup Additional featuresID Display Voice Volume Wiegand Output SetupVoice Volume Setup Wiegand Output not USE Not USE ONE Time Read  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features Version Check Input Test Output Test Keypad Test Last UpdateLCD Test Press ANY KEY Memory Test RAM TESTING…Reader Test Reader Test SCANNING… Communication Test Comm Test Input Type Input Type SetupO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Other information Menu Structure Menu Structure of the F4 button Menu Structure of the F3 buttonF3 button F4 button F5 button Menu Structure of the F5 buttonOther Information Menu Structure of the F6 button F6 button Menu Structure of the F7 button Menu Structure of the F8 button Menu Structure of the F12 button Menu Structure of the F9 buttonF9 button F12 button Duress Alarm Default SettingsOutput Settings for Input Sources TTL#1 TTL#2 Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Communication between CardBuzzer keeps beeping Controller and the Host PC fails Product Specifications Product speciﬁcations Correct disposal of batteries in this product