troubleshooting
PROBLEM |
|
|
|
|
|
|
| SOLUTION |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||
The “ACCESS DOOR ERR” message | 1) | If the unit used to operate properly before, it is likely that there has been an electric shock | |||||||||||
appears when a RF ID card is being read. |
| that damaged the internal memory and data. |
|
|
| ||||||||
|
|
| Please initialize the unit as instructed in the manual. |
|
|
| |||||||
| 2) | Check if the ID information has been entered correctly during its registration. | |||||||||||
|
| - Check if the value for RD is set correctly during the ID registration. |
| ||||||||||
|
| - If the RD value is set to “1”, the door opens only when READER 1 reads tthe card, and | |||||||||||
|
| does not open when READER 2 reads the card. If the card is presented to READER 2, the | |||||||||||
|
| “ACCESS DOOR ERROR” message will appear. |
|
|
| ||||||||
|
| - If the RD value is set to “2”, the door opens only when READER 2 reads the card, and does | |||||||||||
|
| not open when READER 1 reads tthe card. If the card is presented to READER 1, the | |||||||||||
|
| “ACCESS DOOR ERROR” message will appear. |
|
|
| ||||||||
|
| - If the RD value is set to either “0” or “3”, the door opens when either READER 1 or 2 reads | |||||||||||
|
| the card. |
|
|
|
|
|
|
|
| |||
| 3) | If the trouble persists after following the procedures above, contact a designated service center. | |||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
The buzzer keeps beeping. | 1) | Check the door status. If the Door Contact sensor is connected and the Door Open | |||||||||||
|
| Timeout Alarm is selected, an alarm is given. |
|
|
| ||||||||
| 2) | Check the Door Contact sensor type: it must be |
| ||||||||||
| 3) | Check the setup value for BZ in [10. OUTPUT T/S] under the [F5] menu. |
| ||||||||||
|
| This problem can occur if the time schedule code is set to value between 01 and 10 and | |||||||||||
|
| the present time is within the time zone of the selected schedule. |
| ||||||||||
|
|
| If the wrong time schedule is selected, change it to “00” (this can be set by PC software). | ||||||||||
| 4) | Check the Tamper switch of the unit. |
|
|
| ||||||||
| 5) | If the trouble persists after following the procedures above, contact a designated service center. | |||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
The communication between the | 1) | Please check the settings of the application software and the controller. |
| ||||||||||
controller and the Host PC fails. |
| - Check if the COMM ID of the controller is registered on the application software. | |||||||||||
|
| - Set the different COMM ID when two or more controllers are installed. |
| ||||||||||
|
| - Check if the communication speed (57600bps is default) is the same as the setting on | |||||||||||
|
| the software. |
|
|
|
|
|
|
|
| |||
|
| - Make sure that the PC’s COM port is set correctly on the S/W. |
| ||||||||||
| 2) Check the wiring for communication. |
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||||
|
|
| Product |
|
| PC |
|
| Product |
| PC | ||
|
|
|
|
|
|
|
| Converter | |||||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| RX |
|
| TX |
|
|
|
| The | ||
|
|
| TX |
|
| RX |
|
| RTX(+) |
|
| RTX(+) | from the converter |
|
|
| GND |
|
| GND |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| Product |
| Product |
|
|
| PC | ||||
|
|
|
|
| Converter |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| The | |||||||
|
|
| RTX(+) |
| RTX(+) |
| RTX(+) |
| the Converter | ||||
3)It is recommended to use termination resistors of 120 Ohm between the RTX (+) and RTX
Consult a service center or an electric technician if you are not sure how to do it.
4)When a
5)If the trouble persists after following the procedures above, contact a designated service center.
74_ trouble Shooting
