Reader Test, Memory Test, Ram Testing… | Samsung SSA-S2100/EXP

additional features

READER TEST

This function allows you to test the internal (READER #1) and the external readers (READER #2).

1. Press the F9 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the READER TEST item and press ENT .

3.Place your card close to the reader. When the card is read successfully, the reader number with the 8-digit card number will be displayed on the screen.

4. Press ESC to move to the parent menu.

6.READER TEST

SCANNING…

6.READER TEST

READER #1 25500363

6.READER TEST

MEMORY TEST

1.Press the F9 SETUP MENU button.

2. Use the buttons	4 and	6 to move to the MEMORY TEST item and	7.MEMORY TEST
press ENT .			7.MEMORY TEST
press ENT .

3.Press ENT to start the test.

4.Please see the pictures below for the screens when the test has succeeded and failed.

RAM TESTING…

<If the test has succeeded >	<If the test has failed>
TEST PASSED!!!	TEST FAILED!!!
PRESS ANY KEY…	PRESS ANY KEY…

5.Press any key to move to the parent menu.

J If the Data Memory has a problem, the “TEST FAILED” message will be displayed on the screen. If this is the case, contact the nearest Service Center for technical support.

62_ additional features

Image 62

Samsung SSA-S2100/EXP manual Memory Test, Reader Test SCANNING…, Ram Testing…

Contents

Standalone Rfid Access Controller Please visit our website Safety information Safety information This device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Input Type Setup Event Memory SetupVoice Volume Setup Default Settings Features Product introduction Door Open Timeout Alarm External I/O PinsForced Door Open Alarm Duress Alarm WHAT’S Included Quick Guide CD Manual LCD AT a GlanceFront Panel Rear Panel Communication status indicatorPin Connector Preliminary connector for extension LED Cable Color Scheme PIN ConnectorPins Signal Cable Color TCP/IP RJ45 Connector Cable Selection Installing the Wall Mount Follow the instructions below to install the wall mount Connecting the Termination Resistor and Diode Bypass Diode Connection EARTH-GROUNDING the Communication Cables Host PC Connection Input Connection Output Connection External Reader Connection External Reader Connection Communication Line Connection RS-232 Communication Port Connection Max m RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Please follow the steps below TCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallel Initialization Initializing the system using the Initialize switchSystem Initialization in Master Mode Initializing the System To register a master card To Access the Master ModeRegistering a Master ID 00/00 Name DisplayTo register a master card PIN MAX User Setup User Count SetupLanguage Setup € English € Espanol € Portuguese SET DATE/TIME DATE/TIME SetupCommunication Address Setup Comm Addr SET Default SET Baud Rate SetupFactory Defaults Baud Rate Reader #2 Mode Reader mode setupReader #1 Mode Reader #2 KEY Input € USE If set, you can get access using the keypad inputReader #1 KEY Input RD#1 KEY Input not USE User management Registering ID in Quick ModeQuick Mode Registration To register ID SCANNING… Registering the IDTo register the ID card PW TA TB C RD MA MB LV ID Registered SSA-S2101 Numeric letters in 4 ~ 8 or 10 digits To register the PIN numberTo select PIN PW TA TB C RD MA MB LV ID Registered User Management ID List To Delete IDViewing the ID List ALL ID Clear To cancel the work, press the buttonTo delete all registered IDs To delete all registered master IDs Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W Master ID CLR Open ALR Time User Management Door Open Alarm Time SetupARM/DISARM ARM/DISARM SET To Check the Number of Events TWO MEN Operation ModeTo move to the TWO MEN Mode item To select USE or not USE, and press ENT . J not USE To Remove ALL Events To Remove the Time Schedule Exit Button Output Time setupDoor Contact Sensor Setup Exit Button Time Setup Auxiliary Input #1 SetupAuxiliary Input #2 Setup AUX INPUT#1 Tamper Alarm Tamper Alarm Output SetupCUT OFF Output Setup CUT OFF Alarm Duress Mode Output Setup ARM/DISARM Output Setup Door Open Timeout Setup Output Setup for Level IDs Accessing Reader #1 Output Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 Time Schedule Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Antipassback Error Output Setup Output Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2 Reader #2 ID Error Output Setup Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 12.RD2 ID Error 13.RD2 T/S Error Time Setup Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 14.RD2 APB Error Output Time SCHEDULE+ID Advanced setupTime Unit Setup Time Unit Unit 1SEC Unit 0.1SEC APB Mode Not USE ALL Clear Antipassback ModeTime Schedule Setup Use the 4 Buttons to specify the interval, day Holiday Setup Code 01 Holiday Code SetupHoliday Code Code 10 RD1 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD2 Mode I T/S Voice I T/S Output Time Schedule SetupVoice Message Time Schedule T/S Code ‘00’ means no Time Schedules are to be applied CUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Voice Volume Wiegand Output SetupVoice Volume Setup Wiegand Output not USE Not USE ONE Time Read  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features Version Check Input Test Output Test Keypad Test Last UpdateLCD Test Press ANY KEY Memory Test RAM TESTING…Reader Test Reader Test SCANNING… Communication Test Comm Test O , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Other information Menu Structure Menu Structure of the F4 button Menu Structure of the F3 buttonF3 button F4 button Other Information Menu Structure of the F5 buttonF5 button Menu Structure of the F6 button F6 button Menu Structure of the F7 button Menu Structure of the F8 button Menu Structure of the F12 button Menu Structure of the F9 buttonF9 button F12 button Duress Alarm Default SettingsOutput Settings for Input Sources TTL#1 TTL#2 Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Communication between CardBuzzer keeps beeping Controller and the Host PC fails Product Specifications Product speciﬁcations Correct disposal of batteries in this product