Additional features, Event Memory Setup | Samsung SSA-S2100/EXP

additional features

EVENT MEMORY SETUP

1.Press the F2 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to EVENT MEMORY and press
	ENT .
3.	Use the buttons	4	and	6	to select either USE or NOT USE and press
	ENT .

• USE : When the event memory is full, it gives out an error message and maintains all events stored in the memory.

NOT USE : Even when the event memory is full, it does not give out an error message. In this case the last event saved in the memory is replaced with the next new one. Select ‘NOT USE’ for standalone use (only for entry access exclusively).

M The default setting is “USE”.

1.EVENT MEMORY

NOT USE

1.EVENT MEMORY

J NOT USE

1.EVENT MEMORY

JUSE

ADDITIONAL FEATURES

ID DISPLAY

1. Press the F2 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the ID DISPLAY item and press
	ENT .
3.	Use the buttons	4	and	6	to select MESSAGE or ID + MESSAGE
	and press ENT .

•MESSAGE : Instead of a text message and the user ID, the text message of “********” will appear on the screen.

ID + MESSAGE : The User ID along with a text message will appear on the screen.

<MESSAGE>	<ID + MESSAGE>
ÂÂÂÂÂÂÂÂ	12345678
ACCESS GRANTED!	ACCESS GRANTED!
MYID	MYID
12/12 16:25 :07	12/12 16:25 :07

2.ID DISPLAY MESSAGE

2.ID DISPLAY

JMESSAGE

2.ID DISPLAY

J ID + MESSAGE

•The “MYID” in the picture is a user name which will be displayed if the ID and name were registered using the provided application software. (See Page 25 for “Name Display”.)

English _ 57

Image 57

Samsung SSA-S2100/EXP manual Additional features, Event Memory Setup, ID Display

Contents

Please visit our website Standalone Rfid Access Controller Safety information Safety information Important Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Voice Volume Setup Event Memory SetupInput Type Setup Default Settings Product introduction Features Forced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress Alarm Quick Guide CD Manual WHAT’S Included AT a Glance Front PanelLCD Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LED PIN Connector Pins Signal Cable ColorCable Color Scheme Cable Selection TCP/IP RJ45 Connector Follow the instructions below to install the wall mount Installing the Wall Mount Bypass Diode Connection Connecting the Termination Resistor and Diode Host PC EARTH-GROUNDING the Communication Cables Input Connection Connection Output Connection External Reader Connection External Reader Connection RS-232 Communication Port Connection Communication Line Connection RS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps below Connect all RS-485 ports of the product in parallel TCP/IP Communication Port Connection System Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the System To Access the Master Mode Registering a Master IDTo register a master card Name Display To register a master card PIN00/00 Language Setup User Count SetupMAX User Setup € English € Espanol € Portuguese Communication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SET Factory Defaults Baud Rate SetupDefault SET Baud Rate Reader mode setup Reader #1 ModeReader #2 Mode Reader #1 KEY Input € USE If set, you can get access using the keypad inputReader #2 KEY Input RD#1 KEY Input not USE Quick Mode Registration Registering ID in Quick ModeUser management To register ID To register the ID card Registering the IDSCANNING… PW TA TB C RD MA MB LV ID Registered To select PIN To register the PIN numberSSA-S2101 Numeric letters in 4 ~ 8 or 10 digits PW TA TB C RD MA MB LV ID Registered User Management To Delete ID Viewing the ID ListID List To cancel the work, press the button To delete all registered IDsALL ID Clear Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLR ARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SET To move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USE To Remove the Time Schedule To Remove ALL Events Door Contact Sensor Setup Time setupExit Button Output Exit Button Auxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1 CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF Alarm ARM/DISARM Output Setup Duress Mode Output Setup Output Setup for Level IDs Accessing Reader #1 Door Open Timeout Setup Output Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output Setup RD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2 Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID Error Reader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB Error Time Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SEC Time Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, day Holiday Setup Holiday Code Holiday Code SetupCode 01 Code 10 Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/S Voice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be applied Input Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USE ONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version Check Output Test Input Test LCD Test Last UpdateKeypad Test Press ANY KEY Reader Test RAM TESTING…Memory Test Reader Test SCANNING… Comm Test Communication Test Input Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other information F3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 button Menu Structure of the F5 button F5 buttonOther Information F6 button Menu Structure of the F6 button Menu Structure of the F8 button Menu Structure of the F7 button F9 button Menu Structure of the F9 buttonMenu Structure of the F12 button F12 button Output Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2 Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Buzzer keeps beeping CardCommunication between Controller and the Host PC fails Product speciﬁcations Product Specifications Correct disposal of batteries in this product