Copying | Savin 2545/2545p, 3502/3502p, 4502/4502p, 2235, 2245

AdonisC2_ENcopy122F_FM.book Page 62 Thursday, February 15, 2001 3:23 PM

Copying

2

B Press the [Custom Size] key.

C Press the [Vertical mm] key and enter the vertical size of the pa- per with the number keys, then press the [#] key.

Note

❒To change the number en- tered, press the [Clear] or {Clear/Stop} key and enter the new number.

D Enter the horizontal size of the paper with the number keys, then press the [#] key.

Note

❒If the [Horiz mm] key is not highlighted, press the [Horiz mm] key.

❒To change the number en- tered, press the [Clear] or {Clear/Stop} key and enter the new number.

E To register the custom size en- tered, press the [Store] key and then press the [Cancel] key.

Note

❒If you do not register the cus- tom size, go to step F.

❒Only one custom size can be stored.

❒To recall the custom size stored, press the [Recall] key.

❒If you do not register the cus- tom size, the size you set is deleted when modes are cleared.

FPress the [OK] key.

D Set your originals, then press the {Start} key.

E When your copy job is finished, press the {Clear Modes} key to clear the settings.

62

Image 75

Savin 2545/2545p, 3502/3502p, 4502/4502p, 2235, 2245, 2535/2535p manual Copying

Contents

Zdsh000j.eps ⇒ P.237 Power Connection FCC Requirements Means Power ON. c means Stand by Safety During Operation Safety InformationPage Limitation How to Read this ManualSymbols Preparation Table of Contents Sort/Stack/Staple Job Preset Other FunctionsPreset Reduce/Enlarge Basic Functions 121 101112 116 161 149151 156 207 198202 206 239 235236 238Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server ⇒ P.77 ⇒ P.39⇒ P.37 103 Guide To Components Ventilation hole Bypass tray Right side cover Output Tray Guide To copy onto normal paper and thick paperTo copy onto OHP transparencies and translucent paper Options Control Panel Function keys Function Status indicatorClear/Stop key Number keys Display Panel Displays and Key OperationsInitial copy display Document Server initial display Function menu Function List Based on Options Set the paper of the same size KL in the paper trays Main power switch left side of the ma- chine Turning On the PowerTurning On the Main Power Operation switch right side of the control panel Turning On the Power Turning Off the PowerPress the operation switch to make the On indicator goes on Turning Off the Main Power Changing Modes Non-recommended originals for the document feeder OriginalsMetric version Inch version Sizes difficult to detect Sizes Detectable by the Auto Paper Select Missing Image Area Exposure glassDocument feeder Recommended Paper Sizes and Types Copy Paper Ify the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Paper Storage Non-recommended Paper Toner Toner StorageUsed Toner Basics Set your originals Basic ProcedureMake sure that the machine is in Copy mode Make sure that there are no previ- ous settings remaining System Reset Lower the platen cover or docu- ment feeder Setting OriginalsSetting Originals on the Exposure Glass Lift the platen cover or the docu- ment feeder Turn Setting Originals Document FeederOriginal Orientation Standard Orientation Press the Batch key Setting Special OriginalsBatch mode Press the key Press the OK key Mixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Make sure that the Auto Image Den- sity key is selected Press the Lighter or Darker key to adjust the density Selecting Original Type Setting Selecting Copy Paper Auto Paper SelectManual Paper Select Make sure that the Auto Paper Select key is selected Auto Paper Select Rotated copy Auto Reduce/Enlarge Press the Auto Reduce/Enlarge keySelect the paper tray Stack Sort/Stack/Staple Sort Press the Sort or Rotate Sort key Shift Sort After all originals are scanned, press the # key When the 2 Tray Finisher is installedEnter the number of copy sets with the number keys Set the original, then press the Start key Stack Shift StackEnter the number of copies with the number keys Set the original in the same direction as the first one Staple Stapling position and original setting Tray Finisher Sheet Finisher Sort/Stack/Staple Select one of the stapling positions ⇒ P.51 Stapling position and original setting Press the Yes key When Memory Reaches 0%To Remove the Paper from the Staple Unit Press the No key to resume scanning Holes Punch Punch hole positions Select the Punch position Punchable paper sizes are as follows Enter the number of copy sets with the number keys Open the bypass tray Adjust the guides to copy paper size Copying from the Bypass TrayExtender Press the # key When copying onto custom size paper Copying When Copying onto OHP Transparencies or Thick Paper Select OHP Sheet or Thick PaperPress the OK key Set your originals and press the Start key Deleting a Program Storing Your SettingsPrograms Storing a Program Press the Do not Register key Make sure the program settingsDeleting a Program Repeat steps E and F in Storing a Program Recalling a Program Press the To Printing key Job PresetPress the Copy key Set up the next copy job Cancel key Press the Interrupt key Energy Saver Mode Interrupt CopyOther Functions To interrupt an original being fed Set your original Press the Start key Original BeeperSample Copy To interrupt copying after all originals have been fed Press the Clear/Stop key when Copying is displayed Press the Continue keyPress the Change Quantity key Ratio % Paper size Preset Reduce/Enlarge Create Margin mode Press the Reduce/Enlarge keyPress the Enlarge or Reduce key Press the Mag. Ratio key Adjust the ratios with the n or o keyZoom Enter the ratio Enter the desired ratio with the number keys Press the Reduce/Enlarge key Press the Specifid Ratio key Size Magnification Press the OK key Set your original, then press the Start key