Sears 113.241591 owner manual MOTOR SPECIFiCATiONS AND, Electrical Requirements, PowE.LEAD

MOTOR SPECIFiCATiONS AND

This saw is designed to use a 3450 RPM motor only. Do not use any motor that runs faster than 3450 RPM. It is wired for operation on 110-120 volts, 60 Hz., Alternating current. IT MUST NOT BE CONVERTED TO OPERATE ON 230 VOLTS.

The Black and Red motor leads are connected to quick connect tabs "A" and "B" on terminal board.

WARNING: Do not change any of these connec- tions with current on.

POWER LEAD TS BLACK

REW

PowE.LEAD'--'

CAUTION: Oo not use blower or washing machine

motors or any motor wifh an automatic reset overload protector as their use may be hazardous. For replacement motor refer to parts list in this manual.

CONNECTING TO POWER SOURCE OUTLET

This saw must be grounded while in use to protect the operator from electrical shock.

If power cord is worn or cut, or damaged in any way, have it replaced immediately.

If your saw is for use on less than 150 volts it has a plug that looks like below.

		3-PRONG	PLUG
/,DI
0		\
/n	gt
		GROUNDING	PRONG
I t_	I.
		PROPERLY	GROUNDED
		3*PRONG	OUTLET

Plug power cord of fully assembled saw into 110- 120V properly grounded type outlet protected by a 15-am p. time delay or Circuit-Saver fuse or circuit breaker.

IF YOUR ARE NOT SURE THAT YOUR OUTLET IS PROPERLY GROUNDED, HAVE IT CHECKED BY A QUALIFIED ELECTRICIAN.

WARNING: DO NOT PERMIT FINGERS TO

TOUCH THE TERMINALS OF PLUG WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM THE OUTLET.

WARNING: IF NOT PROPERLY GROUNDED THIS POWER TOOL CAN INCUR THE POTENTIAL HAZARD OF ELECTRICAL SHOCK PARTICU- LARLY WHEN USED IN DAMP LOCATIONS, IN PROXIMITY TO PLUMBING, OR OUT OFDOORS.

SUCH AS YOUR HANDS CONTACTING THE SAWBLADE.

ELECTRICAL REQUIREMENTS

This saw is equipped with a 3-conductor cord and

grounding type plug which has a grounding prong, approved by Underwriters' Laboratories and the Canadian Standards Association. The ground conductor has a green lug and is attached to thetool housing at one end and to the ground prong in the attachment plug at the other end.

This plug requires a mating 3-conductor grounded type outlet as shown.

If the outlet you are planning to use for this saw is of the two prong type DO NOT REMOVE OR ALTER THE GROUNDING PRONG iN ANY MANNER. Use an adapter as shown and always connect the grounding lug to a known ground.

it is recommended that you have a qualified electrician replace the TWO prong outlet with a properly grounded THREE prong outlet.

A temporary adapter as shown below is available for connecting plugs to 2-prong receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as to a properly grounded outlet box.

A temporary adapter as illustrated is available for connecting plugs to 2-prong receptacles. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.

GROUNDING LUG

ADAPTER

WARNING: THE GREEN GROUNDING LUG EXTENDING FROM THE ADAPTER MUST BE

CONNECTED TO A PERMANENT GROUNE SUCH AS TO A PROPERLY GROUNDED OUTLE1 BOX. NOT ALL OUTLET BOXES ARE PROPERL_ GROUNDED.

If you are not sure that your outlet box is properl_ grounded, have it checked by a qualified electrician

NOTE: The adapter illustrated is for use only if yoL

already have a properly grounded 2-pron_ receptacle.

The use of any extension cord will cause some los,'

of power. To keep this to a minimum and to preven over-heating and motor burn-out, use the tab!_ below to determine the minimum wire size (A.W.G. extension cord, Use only 3 wire extension cord,, which have 3 prong grounding type plugs and 3. pole receptacles which will accept the plug on th_

SBW.

The motor must rotate COUNTERCLOCKWISI

when viewed from the shaft end.

1 H,P. MOTOR 110-120V

Extension Cord Length Wire SIze A.W.G.

Up to 50 Ft			14
50 to	100	Ft	12
100-	200	Ft	10
200 - 400		Ft	8