BLADE GUARD NOT SHOWN FOR PICTURE CLARITY
NEVER OPERATETHE SAW WITHOUTTHE .......
PROPERINSERTIN PLACE. USE THE SAW
BLADEINSERTWHENSAWING, . . USE THE
COMBINATION DADO MOLDING INSERT (9- 22271) WHEN DADOING OR MOLDING.
<._>il/
BLOCK
:)R NUT
LOOSE
COLLAR
ARBOR
SCREW | _@_ | ARBOR NUT |
| ||
TEETH POINTING |
| |
FRONT OF SAW | t%... |
|
9REMOVING AND INSTALLING SAWBLADE.
WARNING: TO AVOID INJURY DUE TO ACCIDENTAL START, TURN SWITCH "OFF"
AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE REMOVING OR iNSTALLiNG SAWBLADE.
A.Raise Blade Guard ... remove insert.
B.To REMOVE blade, place a block of wood against front of blade. _. PULL arbor wrench toward you to LOOSEN arbor nut.
10
The "yellow" plastic disc imbedded in the table in front of the sawblade, is provided fol marking the location of the "sawcut" on the workpiece.
A.Check disc ... if it is above table surface
place a piece of hardwood on top of it and ta!: it down.
B.With blade 90 ° (square to table) cut off
C.Pull miter gauge back until wood isover disc Using very sharp pencil, mark a line on disc
D.With miter gauge in right hand g roove, follow
same procedure and mark another line or disc.
E.These lines indicate the "path" of the cu'
|
|
|
|
|
|
|
|
|
|
| //,_ |
| (kerf) | made | by the | sawblade. |
|
|
|
|
|
|
|
|
|
| ..... |
|
| ///_\ _'- | F. When | cutting | the workpiece, | line | up mark | or | |||
|
|
|
|
|
|
| _P,_I_#(_H | ///////_L_ |
| workpiece With line | on disc. |
|
|
| |||||
|
|
|
|
|
|
|
|
|
| i!fF y |
| usethehold- ownc .mp(optionalaccessor | |||||||
WOODSLOCK |
|
| 'BOR NU." | i_J | \\\' | on the miter gauge for greater | accuracy. |
| |||||||||||
|
|
|
|
| j// |
|
|
| @ |
|
|
|
|
| |||||
BLADE |
| GUARD | NOT | SHOWN | FOR | PICTURE | CLARITY |
| _P_I_J__I_ |
|
|
|
|
|
| ||||
C. TO | TIGHTEN | arbor nut, place a block | of |
|
|
|
|
| _ | ||||||||||
wood against rear of blade... | PUSH | wrench |
| _'_ |
|
|
| ||||||||||||
away from | you. |
|
|
|
|
|
|
| _ |
|
|
| , | _ | |||||
teeth | are pointing | toward,he,rootofthesaw |
| _ |
| _._._.,___ | Z |
| |||||||||||
When installin_l | the blade | . . . make | sure |
|
|
| |||||||||||||
. | andthatthebladeandcollarsareclean |
| and | __ | " _ | _ |
|
|
| ||||||||||
free | from any burrs. |
|
|
|
|
|
|
|
|
|
| ||||||||
The | HOLLOW | side | of the | collar | must | be | _ | y | _ |
| __L__.__ |
|
| ||||||
against the | blade. |
|
|
|
|
|
|
| BLADE GUARD NOT | SHOWN | FOR PICTURE | CLARITY |
| ||||||
Always tighten the arbor nut securely. |
|
|
|
|
| F |
|
|
| ||||||||||
NOTE: When using the Dado or Molding Head, |
|
|
|
|
|
|
| ||||||||||||
it s not necessary to install the loose collar. |
|
|
|
|
|
|
|
| |||||||||||
To | replace | insert. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Place insert into insert opening in table and |
|
|
|
|
|
|
|
| |||||||||||
push toward rear of saw to engage spring clip |
|
|
|
|
|
|
|
| |||||||||||
and until keyslot | in insert will | drop | over screw. |
| _" |
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ,¢ |
|
|
|
|
|
|
Do not tighten screw to the point where it will deflect the insert.
