Temperature Control | Seiko Group IP-6600 guide

Temperature Control

The following are three conditions for heater control.

(1) Preset temperature maintaining condition

Function:	To heat the paper for reduction of ink dry time,
	improvement of ink fixing, and paper winkles
	protection.
Status:	Status of maintaining the heater temperature at
	preset temperature.
Conditions:	(1) In case the heater is turned ON on the heater
	control panel and the heater ON command
	is received from the engine control board.

(2)In case the status is the same as the (1)’s and the status until the specified delay time after receiving the heater OFF command.

(3)In case of heater test.

(2)Standby temperature maintaining condition

Function:	To shorten time reaching the preset temperature
	at print start.
Status:	Status of maintaining the heater temperature at the
	specified standby temperature (35 °C) for
	all heaters.
	When the preset temperature is lower than the
	specified stand by temperature (35 °C), the printer
	maintaines the preset temperature.
Condition:	In case of time specified as the standby time after
	completion of the preset temperature maintaining
	condition.

4-2

Image 154

Seiko Group IP-6600 manual Temperature Control

Contents

Océ CS6060 Page Introduction Page Deliverables Basic components Accessories Options IiiConsumables Safety Precautions Example of symbolsPage Page Vii Regular Inspection and Maintenance Handling PrecautionsPower Supply Printer Consumables Marks Manual Legend Notational rulesThis mark is followed by a reference section or page number Press To enter Function menu Notation of Keys/LCDs/LEDsExample 1 Keys and messages shown on the LCDs in the text Xii Initializing Wait a Moment Print Ready Roll 64 Coated Table of Contents Basic Operations Operation Procedure for Choice Input, Value Input Operation Panel Menu Operations Printer Specifications Options Consumables Getting Started Getting Started Basic knowledge Operating Conditions Installation SpaceInstallation and maintenance space Height direction Unit mm Environmental Conditions Operating temperature and humidity levelsTemperatures of 20 to 25 C To obtain better print quality, use the printer within Places where the printer must not be installed Media/Paper ConsumablesAvailable media types Precautions for disposing of paper Precautions for storing mediaPrecautions for use Precautions for handling prints Other precautions Ink types InkUse our recommended ink cartridges listed below Item No Ink color Ink capacity Getting Started Basic knowledge Use our recommended waste ink bottle listed below Waste Ink BottleItem No Remarks Use our specified cleaning liquid Maintenance KitItem No Remarks Quantity Cleaning Kit Storage Kit External Views, Part Names, and Functions Front Rear Heater Operation Panel Functions of LCD, LEDs and keys Function Heater Control Panel LCD Exhaust Attachment Option Dryer 64 OptionRoll Cover 64 Option PS RIP PhotoPrint 4 DX Option Printer is being initialized LCD Messages and Printer StateMessages on the LCD Printer can receive data from the computer Printer is drying the media Printer is printingPrinter is paused Online state print information mode display Paper total count and ink removing amount are displayed Printer is shutting down Menus can be operated in offline modeOffline menu mode display Shutdown state displayPage Basic Operations Basic Operations Connection procedure Connecting with ComputerSystem configuration connection example Turn the printer and the computer OFF Set the ID switch on the rear of the printer Set the terminator on the rear of the printer to on or OFF Turning the Power On/Off Printer Turn on the power ON/OFF switch on the operation panel Turning the Power OnTurn on 1 the printer switch on the left rear Printer Turn on Heater Turn on the heater switch on the right rear of the printer To turn the heater on Turning the Power Off Section Heater switch OFF Open the rear cover and slide the media edge guards to Installing Paper Roll in the PrinterReplacing the Paper Roll Both edge of the platen Tighten the left flange knob securely Slide the left flange movable side and put it intoPaper roll Pull the winder sensor lever to front side Paper setting direction Feed the paper until a buzzer sounds from the paper feeder Confirm the media edge guard setting again Push down the pressure roller up/down lever Select either paper roll or cut sheet When registering a new paper typeSelect a paper type Paper will be set automatically Loose the left flange knob, pull out the paper roll from Removing the Paper Roll from the PrinterFlange, and remove the paper roll from the printer Replacing Empty Paper Roll Replacing Paper Roll with AnotherReplacing Jammed Paper Roll Installing/Removing Cut Sheet in/from the Printer Open the ink cover Ink Cartridge Replacement ProcedureReplacing Ink Cartridges Remove an ink cartridge from the printer Insert a new ink cartridge into the printer Basic Operations End of ink cartridge replacementClose the ink cover Guidance message appears Replacement ProcedureReplacing Empty Ink Cartridge Replace the ink cartridge according to the Ink Cartridge If an Ink Cartridge Is Not Installed If an Ink Cartridge Is Not Detected Loosen the knob and lift up the lever from the waste ink Waste Ink Bottle Replacement ProcedureReplacing the Waste Ink Bottle Bottle Select YES and press the key If the Waste Ink Bottle Is Full Guidance message appears on the LCD If the Waste Ink Bottle Is Not InstalledInsert a new waste ink bottle into the printer and install Waste ink bottle cover Press Key to enter the head cleaning menu Head Cleaning CleaningPress Key to display the Cleaning menu Press Key Cleaning takes several minutes When the cleaning is completed, the screen is retured toPress Key to return to the original offline mode Press Key again Press Key to display the Feed menu Paper Feed FeedHold down Key Using the Origin Point Setting Function Origin Point Setting Input the base point print offset value for paper width Input the paper width and press KeyDirection origin point Select *Yes or No of back feed operation Select a paper type again Prepare the paper tube and 1 m-lead paper of which Installing Paper on WinderPaper width is the same as the paper’s you will use Tighten the right flange knob securely Slide the right flange movable side and insert it intoPaper tube Lift the pressure roller up/down lever, insert paper from Manually turn the scroller flange in the direction Tape the edge of the paper on the lead paper at threePositions both sides and center Winding to wind the paper slightly Slack winding Set the tension roller to the upper side Winding unit switch setting Changing Heater Control Setting Temperature Precautions for setting the heater temperature Heater preset temperature by medium Front Print Rear Using the Media Pressure Alternation Lever Using the Head Up/Down Lever Tighten the head fixing screws 2 pieces Using the Media Edge Guard Using the FAN Guard Positioning Bar Using the Print Pause/Restart and Cancel Keys Regular inspection and maintenance guide Inspection & MaintenanceCategoly Inspection/Maintenance To be Referred Capping Unit Cleaning Wiper Blade Cleaning Inspection & Maintenance Test Print Every one month inspection and maintenance Wiper sponge cleaningHead Cleaning Waste Ink Bottle Disposal Off state Head Wash Ink Charge After Head Washing Section Ink Charge After Head Washing Inspection & Maintenance Cleaning outer case Cleaning platen Use a ø3 mm mini-cotton swab Page Operation Panel Menu Operations Operation Panel Menu Operations Menu has the following hierarchical structures Basic Menu OperationMenu Hierarchical Structure Sub-menus of the menu group Menu Tree # Cleaning Mode 01 Mode Data Panel Head ADJ1 #HEAT HW Version Key Set a parameter Switch between menu group screens with Keys. keyBasic Operations and Keys Menu selection Select Entry menu with key An example of Print Mode of the Entry menu is given belowSelect Print Mode You can return to 1 with key Select 01 Fine Select menu with key Select Paper Feed ADJ. menu You can return to 1 with key Select Menu Print menu You can return to 1 with key Menu Print menu of the Func menu is given as an exampleSelect Func menu with key Press key to return to 2 without executing the function Select System menu with key When the Scsi ID is selected, it is displayedScsi ID menu of the System menu is given as an example Case 2 To display only If a value is character input for a parameter Select NameThen, modify the value Press keys so that parameter can be changed Character List Press key to determine the parameterKey Menu Operations INK Menu Paper roll Paper MenuCut sheet Parameter Enter a choice. Paper type number 01 to Paper name setting NameEntry Menu Paper selection Select Paper Parameter Enter a value XXX.XX% 97.00 to 103.00% Set a paper feed adjustment valueSet a print mode Set the paper scanning wait time Condition pass setting Condition Pass Print direction setting DirectionSet a print direction Page Set a paper winding mode Not USE Set when the edge guard is not usedSet a paper feed mode Parameter Enter a choice Paper setting mode Paper SET Mode Sets the front heater temperature Celsius Fahrenheiht Preset temperatureNot reach the preset temperature Range To 55 C Heater will be OFF when ** is set Initial temperature setting for the rear heater Rear Heater Sets the platen heater temperature Celsius FahrenheihtSets the rear heater temperature Celsius Fahrenheiht Sets ON/OFF of the color stripe print Use this for print gradation data Selects a head action modeUse this usually Normal Use this usually Cleaning mode Parameter Enter a value ±2000 pulses +5 mm Pulses=2.5 ∝m Selects a priority of the paper feed adjustment valueSelects a priority of the print mode Gives priority to data Heater mode priority setting Priority Heater Selects a priority of the heater modeDeleting registrated paper Delete Paper Initial values for the registered papers Press the key to change the parameter Press the key to enter to the Entry menuSelect Select Paper menu with the and keys Select a paper number to be registered with the and keys Press the key and revise the parameter Example of parameter settingRegistered is displayed. The display returns to 1 display Paper feed adjustment pattern ADJ Menu Paper feed adjustment correction value setting Feed Adjust Parameter Enter a value xxx.xx% 97.00 to Prints the pattern with high quality and 8-pass mode Prints a pattern for adjusting a paper back feed amountPrints the pattern with standard and 4-pass mode Prints the pattern with high density and 8-pass mode Use this parameter when charging the ink in the printer Service MenuSelects a service cleaning parameter Service cleaning Service Parameter Execution form None Cap cleaning CAP CleaningWiper cleaning Wiper Cleaning Filling ink to the cap Fill CAP Head height Cleaning Menu Feed Menu Prints error log information saved in the printer Prints information on the unit and panel settingsFunc Menu Adjust Menu Adjustment pattern print Adjust Pattern Head position adjustment Lm/Lc/Y/M/C H-POS ADJ YY Reciplocating position Left adjustment Bk/Lm/Lc/Y/M/C Reciplocating position Reight adjustment Bk/Lm/Lc/Y/M/C Displays English messages Displays the Boot versionSystem Menu Displays the engine-SCSI firmware version Displays the version number of the Scsi board WIM Displays the ICB board versionDisplays the Asic version Sets system date used in the unit Displays the heater hardware versionParameter Enter a value 00/01/01 to 99/12/31 Factory setting Initial SET Sets all parameter values to factory settingsSystem time setting System Time Sets system time used in the unit Reset Menu After resetting, the printer goes online Heater Controller Operation Heater Controller Operation Temperature Control ControllerOperation Temperature Control Stop ConditionHeater LDC Display Display in normal modeDisplay AAA to CCC, YYY to ZZZ Display at exiting of the heater Turn on Heater Power Switch massage is displayed on the LCDDisplay when heater AC power is turned OFF Display at heater OFF Setup items and parameters Parameter Setup ModeSetup items and parameters are listed in the table below Entering the parameter setup mode Selecting the setup item Moving the setup itemShows blinking Selecting a setting value Deciding the setting value Move to the last setup item, Exit menuExiting from the parameter setting mode System error Error MessagesRelay board cannot be detected Switch test error occurs in the diagnostics Zero cross error occurs in the diagnostics Troubleshooting Troubleshooting Troubleshooting Items to be checked Clearing Paper Jam Open the lever and rear cover POC error When an Error Message AppearsService Call Errors Nnnn Error code Engine error Communication Errors = Basic Operations Ink Cartridge Replacement Operator Call ErrorsFollowing errors can be corrected by the operator Ink cartridge = Troubleshooting Clearing Paper Jam = Basic Operations Waste Ink Bottle Replacement= Basic Operations Waste Ink Bottle Replacement Paper jam Waste ink bottle = Basic Operations Paper Replacement Paper Others When the Printer Fails to Work Correctly Measures to be taken when the printer malfunctions When a Print Error Occurs Symptom Possible cause Corrective measure When There Is an Abnormal Sound Appendix Appendix Printer Specifications Basic SpecificationsBasic printer specifications Options Options/ConsumablesOptions Name Item number Quantity Remarks Cleaning Liquid Name Item number Quantity Remarks Consumables Ink Name Item number Quantity Remarks Celsius and Fahrenheit Conversion List