Press the key and revise the parameter

Menu Operations

2.Example of parameter setting

In this example, a paper feed adjustment value will be entered.

(1) Select "FEED ADJUST" menu with the and keys.

#FEED ADJUST

>02 : 099.80%

(2) Press the key and revise the parameter.

#FEED ADJUST

*02 : 099.80%

NOTE

-Determine the paper feed adjustment value by printing the paper feed adjustment pattern or according to our information.

(3)Press the key to display the massage.

(This message will be displayed at new registration only.)

#FEED ADJUST

>02 : ENTRY OK?

(4)When the key is pressed, the paper number 02 is registered newly and "*" mark that shows the paper has already

registered is displayed. The display returns to (1) display.

#FEED ADJUST

>02 : 099.80%

Press the key to stop the new registration. The display returns to (1) display.

Section 3 Operation Panel Menu Operations

3-31

Page 135

Image 135

Seiko Group IP-6600 Press the key and revise the parameter, Registered is displayed. The display returns to 1 display

Contents

Océ CS6060 Page Introduction Page Basic components Deliverables Accessories Iii OptionsConsumables Example of symbols Safety PrecautionsPage Page Vii Printer Handling PrecautionsPower Supply Regular Inspection and Maintenance Consumables Manual Legend Notational rules MarksThis mark is followed by a reference section or page number Notation of Keys/LCDs/LEDs Press To enter Function menuExample 1 Keys and messages shown on the LCDs in the text Initializing Wait a Moment Print Ready Roll 64 Coated Xii Table of Contents Basic Operations Operation Panel Menu Operations Operation Procedure for Choice Input, Value Input Options Consumables Printer Specifications Getting Started Basic knowledge Getting Started Height direction Unit mm Installation SpaceInstallation and maintenance space Operating Conditions To obtain better print quality, use the printer within Operating temperature and humidity levelsTemperatures of 20 to 25 C Environmental Conditions Places where the printer must not be installed Consumables Media/PaperAvailable media types Precautions for storing media Precautions for disposing of paperPrecautions for use Other precautions Precautions for handling prints Item No Ink color Ink capacity InkUse our recommended ink cartridges listed below Ink types Getting Started Basic knowledge Waste Ink Bottle Use our recommended waste ink bottle listed belowItem No Remarks Maintenance Kit Use our specified cleaning liquidItem No Remarks Quantity Storage Kit Cleaning Kit Front External Views, Part Names, and Functions Rear Heater Operation Panel Function Functions of LCD, LEDs and keys LCD Heater Control Panel PS RIP PhotoPrint 4 DX Option Dryer 64 OptionRoll Cover 64 Option Exhaust Attachment Option Printer can receive data from the computer LCD Messages and Printer StateMessages on the LCD Printer is being initialized Printer is printing Printer is drying the mediaPrinter is paused Paper total count and ink removing amount are displayed Online state print information mode display Shutdown state display Menus can be operated in offline modeOffline menu mode display Printer is shutting downPage Basic Operations Basic Operations Turn the printer and the computer OFF Connecting with ComputerSystem configuration connection example Connection procedure Set the ID switch on the rear of the printer Set the terminator on the rear of the printer to on or OFF Printer Turning the Power On/Off Printer Turning the Power OnTurn on 1 the printer switch on the left rear Turn on the power ON/OFF switch on the operation panel Turn on Heater To turn the heater on Turn on the heater switch on the right rear of the printer Section Turning the Power Off Heater switch OFF Both edge of the platen Installing Paper Roll in the PrinterReplacing the Paper Roll Open the rear cover and slide the media edge guards to Pull the winder sensor lever to front side Slide the left flange movable side and put it intoPaper roll Tighten the left flange knob securely Feed the paper until a buzzer sounds from the paper feeder Paper setting direction Push down the pressure roller up/down lever Confirm the media edge guard setting again When registering a new paper type Select either paper roll or cut sheetSelect a paper type Paper will be set automatically Removing the Paper Roll from the Printer Loose the left flange knob, pull out the paper roll fromFlange, and remove the paper roll from the printer Replacing Paper Roll with Another Replacing Empty Paper RollReplacing Jammed Paper Roll Installing/Removing Cut Sheet in/from the Printer Remove an ink cartridge from the printer Ink Cartridge Replacement ProcedureReplacing Ink Cartridges Open the ink cover Basic Operations End of ink cartridge replacement Insert a new ink cartridge into the printerClose the ink cover Replace the ink cartridge according to the Ink Cartridge Replacement ProcedureReplacing Empty Ink Cartridge Guidance message appears If an Ink Cartridge Is Not Installed If an Ink Cartridge Is Not Detected Bottle Waste Ink Bottle Replacement ProcedureReplacing the Waste Ink Bottle Loosen the knob and lift up the lever from the waste ink Select YES and press the key If the Waste Ink Bottle Is Full Waste ink bottle cover If the Waste Ink Bottle Is Not InstalledInsert a new waste ink bottle into the printer and install Guidance message appears on the LCD Press Key Head Cleaning CleaningPress Key to display the Cleaning menu Press Key to enter the head cleaning menu Press Key again When the cleaning is completed, the screen is retured toPress Key to return to the original offline mode Cleaning takes several minutes Paper Feed Feed Press Key to display the Feed menuHold down Key Origin Point Setting Using the Origin Point Setting Function Input the paper width and press Key Input the base point print offset value for paper widthDirection origin point Select a paper type again Select *Yes or No of back feed operation Installing Paper on Winder Prepare the paper tube and 1 m-lead paper of whichPaper width is the same as the paper’s you will use Lift the pressure roller up/down lever, insert paper from Slide the right flange movable side and insert it intoPaper tube Tighten the right flange knob securely Winding to wind the paper slightly Tape the edge of the paper on the lead paper at threePositions both sides and center Manually turn the scroller flange in the direction Slack winding Set the tension roller to the upper side Winding unit switch setting Precautions for setting the heater temperature Changing Heater Control Setting Temperature Front Print Rear Heater preset temperature by medium Using the Media Pressure Alternation Lever Using the Head Up/Down Lever Tighten the head fixing screws 2 pieces Using the Media Edge Guard Using the FAN Guard Positioning Bar Using the Print Pause/Restart and Cancel Keys Inspection & Maintenance Regular inspection and maintenance guideCategoly Inspection/Maintenance To be Referred Capping Unit Cleaning Wiper Blade Cleaning Test Print Inspection & Maintenance Waste Ink Bottle Disposal Wiper sponge cleaningHead Cleaning Every one month inspection and maintenance Off state Ink Charge After Head Washing Head Wash Section Ink Charge After Head Washing Inspection & Maintenance Cleaning outer case Cleaning platen Use a ø3 mm mini-cotton swab Page Operation Panel Menu Operations Operation Panel Menu Operations Sub-menus of the menu group Basic Menu OperationMenu Hierarchical Structure Menu has the following hierarchical structures Menu Tree # Cleaning Mode 01 Mode Data Panel Head ADJ1 #HEAT HW Version Menu selection Switch between menu group screens with Keys. keyBasic Operations and Keys Key Set a parameter Select 01 Fine An example of Print Mode of the Entry menu is given belowSelect Print Mode You can return to 1 with key Select Entry menu with key Select Paper Feed ADJ. menu You can return to 1 with key Select menu with key Press key to return to 2 without executing the function Menu Print menu of the Func menu is given as an exampleSelect Func menu with key Select Menu Print menu You can return to 1 with key Case 2 To display only When the Scsi ID is selected, it is displayedScsi ID menu of the System menu is given as an example Select System menu with key Press keys so that parameter can be changed Select NameThen, modify the value If a value is character input for a parameter Press key to determine the parameter Character ListKey INK Menu Menu Operations Paper Menu Paper rollCut sheet Paper selection Select Paper Paper name setting NameEntry Menu Parameter Enter a choice. Paper type number 01 to Set the paper scanning wait time Set a paper feed adjustment valueSet a print mode Parameter Enter a value XXX.XX% 97.00 to 103.00% Print direction setting Direction Condition pass setting Condition PassSet a print direction Page Parameter Enter a choice Not USE Set when the edge guard is not usedSet a paper feed mode Set a paper winding mode Paper setting mode Paper SET Mode Range To 55 C Heater will be OFF when ** is set Preset temperatureNot reach the preset temperature Sets the front heater temperature Celsius Fahrenheiht Sets ON/OFF of the color stripe print Sets the platen heater temperature Celsius FahrenheihtSets the rear heater temperature Celsius Fahrenheiht Initial temperature setting for the rear heater Rear Heater Normal Use this usually Selects a head action modeUse this usually Use this for print gradation data Cleaning mode Gives priority to data Selects a priority of the paper feed adjustment valueSelects a priority of the print mode Parameter Enter a value ±2000 pulses +5 mm Pulses=2.5 ∝m Selects a priority of the heater mode Heater mode priority setting Priority HeaterDeleting registrated paper Delete Paper Initial values for the registered papers Select a paper number to be registered with the and keys Press the key to enter to the Entry menuSelect Select Paper menu with the and keys Press the key to change the parameter Example of parameter setting Press the key and revise the parameterRegistered is displayed. The display returns to 1 display ADJ Menu Paper feed adjustment pattern Parameter Enter a value xxx.xx% 97.00 to Paper feed adjustment correction value setting Feed Adjust Prints the pattern with high density and 8-pass mode Prints a pattern for adjusting a paper back feed amountPrints the pattern with standard and 4-pass mode Prints the pattern with high quality and 8-pass mode Service cleaning Service Service MenuSelects a service cleaning parameter Use this parameter when charging the ink in the printer Filling ink to the cap Fill CAP Cap cleaning CAP CleaningWiper cleaning Wiper Cleaning Parameter Execution form None Head height Cleaning Menu Feed Menu Prints information on the unit and panel settings Prints error log information saved in the printerFunc Menu Adjustment pattern print Adjust Pattern Adjust Menu Reciplocating position Left adjustment Bk/Lm/Lc/Y/M/C Head position adjustment Lm/Lc/Y/M/C H-POS ADJ YY Reciplocating position Reight adjustment Bk/Lm/Lc/Y/M/C Displays the engine-SCSI firmware version Displays the Boot versionSystem Menu Displays English messages Displays the ICB board version Displays the version number of the Scsi board WIMDisplays the Asic version Displays the heater hardware version Sets system date used in the unitParameter Enter a value 00/01/01 to 99/12/31 Sets system time used in the unit Sets all parameter values to factory settingsSystem time setting System Time Factory setting Initial SET After resetting, the printer goes online Reset Menu Heater Controller Operation Heater Controller Operation Temperature Control Temperature Control Stop Condition ControllerOperationHeater Display in normal mode LDC DisplayDisplay AAA to CCC, YYY to ZZZ Display at heater OFF Turn on Heater Power Switch massage is displayed on the LCDDisplay when heater AC power is turned OFF Display at exiting of the heater Entering the parameter setup mode Parameter Setup ModeSetup items and parameters are listed in the table below Setup items and parameters Moving the setup item Selecting the setup itemShows blinking Selecting a setting value Move to the last setup item, Exit menu Deciding the setting valueExiting from the parameter setting mode Error Messages System errorRelay board cannot be detected Zero cross error occurs in the diagnostics Switch test error occurs in the diagnostics Troubleshooting Troubleshooting Items to be checked Troubleshooting Open the lever and rear cover Clearing Paper Jam Nnnn Error code When an Error Message AppearsService Call Errors POC error Engine error Communication Errors Ink cartridge Operator Call ErrorsFollowing errors can be corrected by the operator = Basic Operations Ink Cartridge Replacement Waste ink bottle = Basic Operations Waste Ink Bottle Replacement= Basic Operations Waste Ink Bottle Replacement Paper jam = Troubleshooting Clearing Paper Jam Paper = Basic Operations Paper Replacement Others Measures to be taken when the printer malfunctions When the Printer Fails to Work Correctly Symptom Possible cause Corrective measure When a Print Error Occurs When There Is an Abnormal Sound Appendix Appendix Basic Specifications Printer SpecificationsBasic printer specifications Options/Consumables OptionsOptions Name Item number Quantity Remarks Consumables Ink Name Item number Quantity Remarks Cleaning Liquid Name Item number Quantity Remarks Celsius and Fahrenheit Conversion List

Seiko Group IP-6600 manual Press the key and revise the parameter, Example of parameter setting

Models: IP-6600

2.Example of parameter setting

(2) Press the key and revise the parameter.

registered is displayed. The display returns to (1) display.

Section 3 Operation Panel Menu Operations