Precautions, Installation | Sharp AR-650 guide

PRECAUTIONS

1.INSTALLATION

1The copier should be installed by a qualified service technician.

Note: The packing material should be disposed of properly.

2	To obtain the best possible results, this copier should be used in conjunction with a
	dedicated AC power line at the following ratings:
	115V–60 Hz, 16 A

Notes:

1.The use of other appliances or other equipment on the same line as this copier may adversely affect performance and copy quality.

2.Be sure to use a 3-conductor, grounded wall outlet.

3.In areas where a 2-pin plug is used, the copier must be grounded for safety.

Never ground it to a gas pipe, a water pipe, or any other object not suitable for grounding.

3 After a suitable place has been selected for the installation of the copier, please do not change it. Avoid excessive heat, dust, vibration and direct sunlight. Also, provide proper ventilation as the copier emits a small amount of ozone.

Notes:

1.Recommended environmental range for use is as follows:

•Temperature: 10~30˚C/50~86˚F

•Humidity: 20~85% RH

2.To insure optimal operation, allow clearances of at least 32" on the left, 32" on the right and 4" in the rear (refer to the illustration below).

4 inches

32 inches

32 inches

PREFACE CONTENTS PRECAUTIONS

The socket-outlet shall be installed near the equipment and shall be easily accessible.

5

Image 9

Sharp AR-650 operation manual Precautions, Installation

Contents

AR-650 For Your Records FCC Notice Off Mode Default Time AR-650 Copier model Base model Off ModeAutomatic Energy Save Default Time Sleep Mode Default Time Preface User Safety Features of the AR-650 copier Table of Contents Table of Contents Installation Precautions Precautions Be sure to disconnect the power-cord plugHandle and use the copier gently and carefully Description of the Digital Copier Certification Label Names of Main Components Description of Optional Equipment Finisher AR-FN8, AR-FN9Hole Punching Unit Description of the Control Panel Clip trayInterrupt key Stop key ALL Clear keyStart key Clear key Description of the Control Panel Description of the Graphic Display Clear Paper symbol Saddle Stitcher JAM SymbolUnit Misfeed symbol Call Service symbol HOW to Make Copies Turning on the Power Switch Turn on the power switch Message Wait Warming Up appearsAbout 7 minutes later, the message Ready appears Auto Job Start Mode When Placing the Original on the GlassSet the desired copy modes Press the Start key Turning on the Power Switch / Auto JOB Start Copies Make Copying in the Continuous Feed Mode Press the Program key on the display panel Copying in the Single-Feed ModePress the ADF key Single feeding Insert the original Press the SET key Copying in the Mixed Originals Mode Mode is selected When Using the Automatic Document FeederCheck that the Automatic Paper Selection Key in the desired copy quantity Select the exposure Copying in the Automatic Paper Selection Mode Press the Zoom ORG.→ Copy key Select the copy size ACTUAL-SIZE Copying by Specifying the Copy Size ACTUAL-SIZE Copying by Specifying the Copy Size Using Automatic Magnification Selection Press the Zoom ORG.→ Copy key Press the AMS keyPress the desired COPY-SIZE key Reduction and Enlargement Copying Selecting the Original Size and the Copy Size Using the Zoom Keys Place the original, key in the copy quantity Press the 1→ 1 key Example of Duplexed Copies from Single-Sided Originals Single-sided originals to duplexed copies Press the 1→ 2 key to select the function Duplexed Copies from SINGLE-SIDED Originals Press the Start key Place the next original second side Duplexed Copies from SINGLE-SIDED Originals Example of Duplexed Copies from Two-Sided Originals Procedure Duplexed Copies from TWO-SIDED Originals Example of Single-Sided Copies from Two-Sided Originals SINGLE-SIDED Copies from TWO-SIDED Originals Select the desired copy size, exposure Copy quantity Example of Duplexed Copies from a Book Original Duplexed Copies from Book Originals Duplexed Copies from Book Originals Margin SelectIf necessary Select the desired exposure, reproduction Copying in the Manual Exposure Mode Copying in the Automatic Exposure ModeMake sure that Auto is displayed Place the original and press the Start key If necessary, press Key To adjust the exposure Copying in the Text or Photo ModePress either Ratio and copy quantity Press the Start key Select the desired exposure and reproduction ratio Bypass Copying Key in the desired copy quantity Press the Start key Place sheets of copy paper on the sheet bypass Select the desired copy size Bypass Copying by Specifying the Copy Size Slides Replace the original with a new original Interrupt CopyingReproduction ratio After interrupt copying is finished, press Presetting of Copy Modes Using the ALL Clear key ALL Clear KEYPress the ALL Clear key Using the Editing Functions Image Shift Copying Example of Image Shift CopyingPress the Edit key to enter the Editing menu Or on the glass SET Example of Edge Erase Copying Edge Erase Copying Usingthe Editing Functions DUAL-PAGE Copying Example of Dual-Page Copying Procedure Example of X-Y zoom Y ZoomSelect the X-Y zoom function in the Editing menu Specify the X and Y reproduction ratios Example of trimming/masking TRIMMING/MASKING How to read areas Place the originalOriginal scale Read the values defining the desired area TRIMMING/MASKINGAs follows Select the editing function in the Editing menu Specify the area of the original Mirror Image Example of mirror image Procedure NEGATIVE/POSITIVE Reversal Example of negative/positive reversalPress the NEG/POS key NEGATIVE/POSITIVE Reversal Examples of 2 in 1 / 4 1 / 4 1 / 4 in 1 Select the 2 in 1 / 4 in 1 function in the Editing menuSelect 2 in 1 or 4 Select the 2 in 1 / 4 in 1 function Select the type of originalEditing menu Press Side Annotation Select where the date and time are to be printedExample of annotation Select the annotation function in the Editing menu Annotation Example of page number Procedure NumberSelect the page number function in the Editing menu Select the page number position NumberKey in the start page number Place the original on the original glass Using the Editing Functions Example of magazine sort Magazine SortSelect the magazine sort function in the Editing menu Set the center margin When the last original has finished being Repeat the aboveScanned, press Key Examples of Cover Sheet Copying Cover Sheet Copying Setting the sheets on the sheet bypass Copying ProcedureSetting a cassette for cover sheet Set the special sheets of paper for Select the desired Cover Sheet mode Cover Sheet CopyingSelect the cover sheet copying function in the Editing menu Key in the desired number of copies or sets Examples of Sheet Insertion Copying Sheet Insertion Copying Designated sheet-insertion cassette Place special sheets of paperSelect the sheet-insertion copying function Press the Edit key to enter the Editing Press the Blank or Copied key Using the digital keys, specify the desiredPress Next To specify the next page, repeat step Setting a Cassette for Cover SHEET/SHEET-INSERTION Copying Setting Procedure Resetting to the Previous Size Procedure 1 Memorize Mode Document StorageSelect the document storage function Document Storage Select the desired exposureSelect the document storage function in the Editing menu Select the number location containing Document you want printedSelect the desired copy quantity Press the Start key Memo Using the Special Functions Following message appears Account NumberKey in a 4-digit account number Make copies as you would normally do Storing a New Combination of Copy Modes JOB MemorySelect the job memory function Program menu Press the MEMORY1 or, MEMORY2 MEMORY3 , MEMORY4 key JOB Memory Recalling a Stored Combination of Copy Modes Select the job memory function Program menuPress the Recall key to select the recall function JOB Memory How to Set the Weekly Timer Weekly TimerSelect the timer function in the Program Menu How to Cancel the Operation of the Weekly Timer Weekly TimerHow to Use the Copier when Turned OFF Select the timer function in the Program menu 101 Copying Using Paper of Other Sizes Setting the Date and Time 102Key in the last two numbers of the year 103 To change the Automatic Shutoff time To change theAutomatic Energy Save timeTo exit from the Automatic Energy Save time To exit from the Automatic Shutoff time 105 Change of Language on the Display Panel 106 107 Using the Optional Finisher 108 Names of the Main Components 109 NON-SORT CopyingCheck that Ratio and exposure If Sort is not displayed, select the sort Mode Sort Copying110 Key in the copy quantity sets using the digital keys 111Copies exit onto the trays When Placing the Original on the Glass Select the sort mode Sort Copying112 113 Select the group mode Group Copying114 Key in the copy quantity using the digital 115Keys 116 Group Copying 117 Press the desired mode keys Select the staple modeStapling 118 Stapled copies exit onto the trays 119 120 Stapling 121 Hole Punching Mode Select the puncher mode122 Tip Number of punch holes and available paper sizes 123 124 Magazine Sort & Saddle Stitching Mode 125 Perform steps 2 through 5 of the procedure 126Place the original and press the Start 127 When the Graphic Symbols Flash Adding Paper to the Front Cassette ADD Paper Symbol128 Slowly push the cassette straight in until Adding Paper to the Large-Capacity Feeder 129Open the door of the large-capacity feeder Replace Toner BAG Symbol Replacing Procedure130 131 132 ADD Toner Symbol 133 134 ADD Toner Symbol Additional Explanation 135 Misfeeding inside of the Copier Clear Paper Symbol136 Open the exit cover 137 138 Clear Paper Symbol 139 140 141 Misfeeding in the Automatic Duplexer 142 143 144 145 Misfeeding in Pedestal Cassette Feeding Misfeeding from the Large-Capacity Feeder Misfeeding in the Bypass Guide146 Check Original Symbol Removing Procedure147 148 Check Original SymbolResume copying Originals remaining in the original feed tray Raise the paper guide and remove Misfed paper 149 150 Open the cover of the hole punching unitOpen the upper cover of the finisher 151 Lifting up the lever , or leversRemove the misfed paper Saddle Stitcher JAM Symbol 152Lift the release lever and move the finisher 153 Replacing Staples Optional Finisher154 155 Pull out the staple cartridgePulling straight up, remove the seal holding the staples Replacing Staples Optional Reinstall the stapler unit in its previous position156 Set the staple cartridge 157 Saddle Stitcher AR-FN9Remove the staple case and set the new Case 158 Test stapling is automatically carried outBlank copy is made automatically 159 160 Removing Jammed Staples OPTIONALCont 161 Remove the empty staple case 162 163 164 Clearing Accumulated Punched Paper Bits 165 Call Service Symbol 166 Periodic Maintenance 167 Maintenance Daily Inspection Cleaning coversItems to inspect every morning Items to inspect once a week Simple Troubleshooting Copier does not start169 When copies are dirty Copies are not clear170 171 SPECIFICATIONS, Accessories & Options 172 Specifications 173 174 Finisher Specifications OptionalTray Loading Capacity Hole Puncher Options for AR-FN8/AR-FN9Page Sharp Corporation Oration