Chapter 11: SEND/RECEIVE function
[2] RECEIVE
This function operates by the combination of
(1) When the module is used (host PC: JW30H,
UN- | fileN S | ||
OPCH | |||
|
|
|
|
n | D |
| |
SEND |
| ||
|
|
| |
UN | : Module No. switch set value (0 to 6) of the communication |
| module |
CH | : Channel number within the specified module (board) (0 to 3). |
| In the PC program, the same port number can be called 4 |
| times, once for each channel (CH0, CH1, CH2, and CH3). |
ST | : Target node number (01 to FE(H)) |
fileN | : Data area in the target node PC (file number) |
S | : Top file address of the data area in the target node PC |
n: Number of data bytes transmitted (000 to 377(8), 256 bytes at 000)
D : Data area top register of source station data
- Setting range of D
ｺ0000 to ｺ1577 ｺ2000 to ｺ7577 b0000 to b1777 b2000 to b3777 09000 to 99777 E0000 to E7777
File1 000000 to 037777
@ｺ0000 to @ｺ1574 @ｺ2000 to @ｺ7574 @b0000 to @b1774 @b2000 to @b3774 @09000 to @99774 @E0000 to @E7774
File1 @000000 to @037774
|
| This node |
|
|
|
|
|
|
|
| ||
| Setting target node |
|
|
|
| Target node | ||||||
|
|
|
|
| CH number |
| ||||||
|
|
|
|
|
| |||||||
|
| file 0 |
| file N | ||||||||
|
| corresponding to |
| |||||||||
|
|
|
|
|
|
|
|
|
| |||
D → |
|
|
| the UN number | S → |
|
|
|
| |||
|
|
|
|
|
|
| Send |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| n |
|
|
|
|
|
|
| Response |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Flag |
| 11 |
|
|
| |
|
|
| |
|
|
|
|
Flag status during and after the operation |
| ||
| Zero | Carry | Error | Non- |
| |
| carry | Description | ||||
| 07357 | 07356 | 07355 | |||
| 07354 |
| ||||
|
|
|
|
| ||
No response |
|
|
|
| Set value on the UN and module No. switch set | |
from the module | 0 | 0 | 1 | 0 | ||
value of the communication module are different. | ||||||
(board) |
|
|
|
| ||
|
|
|
|
| ||
|
|
|
|
|
| |
|
|
|
|
| This condition may instantaneously occur while | |
Communi- |
|
|
|
| other receive instruction is being executed. | |
0 | 0 | 0 | 1 | However, as soon as the condition becomes clear | ||
cation jam | ||||||
|
|
|
| for the execution of an instruction, the status will | ||
|
|
|
|
| ||
|
|
|
|
| turn to "Communicating." | |
|
|
|
|
|
| |
Communi- |
|
|
|
| The communicating is being run. Once the | |
1 | 0 | 0 | 1 | communication completes, the status will change | ||
cating | ||||||
|
|
|
| to either "normal end" or "abnormal end." | ||
|
|
|
|
| ||
|
|
|
|
|
| |
Normal end | 0 | 1 | 0 | 0 | When the receive instruction has successfully | |
completed. | ||||||
|
|
|
|
| ||
|
|
|
|
|
| |
Abnormal end | 0 | 1 | 1 | 0 | When there is no response from target node. | |
(timeout) | ||||||
|
|
|
|
| ||
|
|
|
|
|
|