Chapter 4: Name and Function of Each Part
4-4 JW-50FL
|
|
|
|
| 2 | 3 | 4 |
|
|
|
|
| |||
|
|
|
|
| |||
|
|
|
|
| 1 |
| 5 |
|
|
|
|
| 0 |
| |
|
|
|
|
|
|
| 6 |
|
|
|
|
| 9 |
| |
| 8 Switch SW3 |
|
|
| 8 | 7 | |
|
|
|
| ||||
|
|
|
|
| SW3 | ||
|
|
|
|
| |||
|
|
|
|
| |||
4 | (Factory setting: 0) |
|
| ||||
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7Switch SW3 (Factory setting: ON)
OFF ON
SW2
| ||
1 LED indicator | LNK | S0 |
TX | S1 | |
| RX | S2 |
| DC12V | S3 |
|
| S4 |
| TEST | S5 |
| PER | S6 |
| HER | S7 |
2 Connector for
P
programmer R
O
G
R
A
M
M
E
R
3 Connector for 10BASE5
10B5
4Connector for
5 12 VDC power | |
supply input terminal | 12VIN |
| (+) |
| (-) |
6 Reset switch | FG |
RESET |
| Name | Function | |
| Display panel | Displays the | |
|
|
|
|
|
| LNK | Lights at operating. Lights OFF at stopping. |
|
|
|
|
|
| TX | Blink at transmitting data. |
|
|
|
|
|
| RX | Blink at receiving data. |
|
|
|
|
1 |
| 12 VDC | Lights when 12 VDC is supplied. (Only when 10BASE5 is used.) |
|
|
|
|
|
| TEST | Lights at test mode. |
|
|
|
|
|
| PER | Lights at parameter setting error. |
|
|
|
|
|
| HER | Lights at this module error. |
|
|
| |
|
| S0 to S7 Indicates status of connection status monitor flag. | |
|
|
|
|
2Connector for programmer When using a remote monitor or remote programming function, connect a
3 | Connector for 10BASE5 | Connect the 10BASE5 transceiver cable. | |
Make sure to slide the lock securely to the "lock" position. | |||
|
|
4Connector for
| 12 VDC power supply | When 10BASE5 is used, connect a commercially available DC power | ||
5 | supply that is designed to supply power to transceivers. The DC power | |||
input terminal | ||||
| supply must provide 12VDC 5% and 0.5 A or more. | |||
|
|
| ||
|
|
|
| |
6 | Reset switch | Only used by SHARP engineers. Users should not press this switch. | ||
|
|
|
| |
|
| ON | Turn ON when the shields on the | |
|
| connectors are connected to the FG (base) of the | ||
|
|
| ||
| Switch SW2 |
|
| |
7 |
| Turn OFF when the shields on the | ||
|
| OFF | connectors are not connected to the FG. | |
|
|
| - Ground the FG line on the 12 VDC connector separately. | |
|
|
|
| |
8 | Switch SW3 | Specify a parameter address (in system memory) from 0 to 4. | ||
- See page | ||||
|
|
|
Note: Only 10BASE5 or