Quiet Detect Start Time | Sharp UX-B30 guide

all.book Page 75 Tuesday, June 1, 2004 4:24 PM

Optional A.M. Mode Settings

Quiet Detect Start Time

This setting can be used to delay the start of the Quiet Detect Time function. For example, if you want to insert a pause at the beginning of your answering machine’s outgoing message to ensure clear detection of fax signals, you can use this setting to delay the start of silence detection so that the pause will not cause the fax to take over the line.

Quiet Detect Start Timing has been turned off (set to “00” seconds) at the factory. If you want to use this function, turn it on by entering a 2-digit number equal to the desired number of seconds of the delay. As general guide, the delay time should be slightly longer than the pause before the outgoing message.

1	Press	once and	3 times.	Display:
1	Press	once and	3 times.
				OPTION SETTING
2	Press	once and	6 times.	QUIET START
3	Press	once.		ENTER (00-15) 00
4	Enter a 2-digit number (from 01 to 15)			The display briefly shows
	for the number of seconds of the delay,			your selection, then:
	or enter 00 to turn off the function.			ON A.M.FAILURE
				ON A.M.FAILURE
	Example: 3 seconds

STOP

5 Press to return to the date and time display.

75

Answering	Machine
5.

Image 79

Sharp UX-B30 manual Quiet Detect Start Time, Enter a 2-digit number from 01 to, For the number of seconds of the delay

Contents

UX-B30 Aviso Quick48 01!AB7 Applicable telephone line Introduction Automatic document feeder Input document size Important safety information All.book Page 4 Tuesday, June 1, 2004 424 PM Table of Contents Making Copies Answering Machine Connection Look at the Operation Panel Hold key Function keyNumber keys Poll key Monitoring phone conversations Unpacking Checklist Installation Open the operation panel Open the print compartment cover Points to keep in mind when setting upAttachments Removing the packing tape Connecting the handset Attaching the paper tray Loading Printing Paper Connecting the Power Cord Replacement cartridge Sharp UX-C70B Installing the Print CartridgePrint cartridge yield at 4% coverage Initial cartridge Make sure the handset is on its cradle When this has happened, press Patrone Holder return to its home position Press Patrone to make the print cartridge Align Cartridge =PRINT,2=SET Press once Quality modeusing more/less inkPress Press once and twice High-quality fax print setting fast/slow printing of faxes Connecting the Telephone Line Cord Germany Other devicesSwitzerland, Austria Enter your fax number by pressing the number keys max digits Entering Your Name and Fax Number Example Sharp = 7777 44 2 777 Press once and once Setting the Date and TimeEnter a two-digit number for the day 01 to Example the 5th Press to start the clock Enter the year four digits Example TEL/FAX mode Setting the Reception ModeMode Press Setting the reception mode Select Long Time if your PBX Line is a high-speed line Flash Select Setting for PBXSelect Short Time if your PBX Line is a normal telephone line Press once and 3 times Setting the Display Language Press To select Volume AdjustmentDesired volume level Speaker If you selected Ringer OFF OK ? to RingerTurn off the ringer, press End beep off Error beep offPress To turn on the error beep or To turn off the error beep Press To turn on the key tone or Key tone offPress To turn on the end beep or To turn off the end beep Sending Faxes Size and weightTransmittable Documents Loading the Document Adjust the document guides to the width of your documentOther restrictions Removing a document from the feeder Resolution settings Adjusting the Resolution and ContrastContrast settings Settings appear in the display One or more times until Desired resolution and contrastLoad the documents Press To set the default resolution Changing the default resolutionTo FINE, or To set it to Standard Sending a Fax by Normal Dialling Sending a Fax by Automatic Dialling When you hear the fax tone, press . Replace the handsetStoring fax and phone numbers for automatic dialling Enter FAX # All.book Page 46 Tuesday, June 1, 2004 424 PM Press for Edit or for Clear Editing and clearing auto-dial numbers Make the desired changes to the name Using an auto-dial numberIf you are sending a fax, load the documents Sending a fax by Direct Keypad Dialling Correct, press Automatic redialling RedialDialling begins Press To select YES, or Error Correction ModeSelect no Dial the receiving machine and send the fax To set the resolution and/or contrastBatch Page Numbering Load the documents Press Once Broadcasting sending a fax to multiple destinations Sending a Fax From Memory Memory transmission When you are ready to begin transmission, press If the memory becomes full Receiving Faxes Using TEL/FAX Mode Pseudo Ring Duration for Tel/Fax Mode Using A.M. ModeEnter a number as follows for the desired duration Changing the number of rings Using FAX Mode Using TEL Mode Using TEL Mode After speaking. Press before Sender presses their Start key Answering with the fax’s handsetDisplay shows Receiving Then replace the handset Phone goes dead Putting a call on hold Stiller Faxempfang Fax Signal Receive Optional Reception SettingsPress To turn on the function, or Enter the desired number any number Changing the number for remote fax activationFrom 0 to Press To select AUTO, or Reception RatioSelect 100% Substitute Reception to Memory Example Two Copies each Three originals Select any of the following copy settings as neededMaking Copies Load the documents face down. Maximum of 10 sheets Copy Cut-off When you are ready to begin copying, pressIf Memory is Full appears Press To turn on high-quality copy High-quality copy setting fast/slow printing of copies Preparations Using the Answering Machine ConnectionSet the reception mode to A.M Answering Machine Connection Set your answering machine to auto answer How answering machine mode operates Quiet Detect Time Optional A.M. Mode Settings Quiet Start Or enter 00 to turn off the function For the number of seconds of the delayQuiet Detect Start Time Enter a 2-digit number from 01 to On A.M.Failure To turn off Caller ID, press Caller ID Requires Subscription to ServiceSpecial Functions Press YES to turn on Caller ID Display messages How Caller ID operates Voice call Press when you have finished viewing the listViewing the Caller ID list Fax Priority Call To delete calls from the Caller ID listPress to store or clear the number Blocking voice calls Press and then press to return to the date and time display Blocking Reception of Unwanted Faxes Press Abruf Polling Requesting a Fax Transmission Making enquiry calls PBX operationsTransferring calls Press to print the list Printing Lists Help List Setup ListTelephone Number List Caller-ID List Headings in the Transaction Report Transaction Report Press a number from To select the condition for printing Transaction Report print condition Then pull the roller to the left and out of the machine MaintenanceCleaning the Machine Cleaning the scanning glass and rollers Replace the white roller, inserting the right end first If the scanning glass is difficult to clean Cleaning the housing Cleaning the paper feed roller Aligning the print cartridge Improving Print Quality Cleaning the print cartridge nozzles All.book Page 94 Tuesday, June 1, 2004 424 PM Wiping the print nozzles and contacts About the lithium battery Cleaning the cartridge holder Problem Solution TroubleshootingProblems and Solutions Line error Dialling and transmission problems Reception and copying problems Answering machine connection General problems Press Start KEY Messages and Signals 102 Printer Error Audible signals Clearing a jammed document Clearing Paper JamsOpen the operation panel Gently remove the document Clearing jammed printing paper Sending Faxes Quick Reference Guide Envoi de télécopies Guide de référence rapide 108 Index 109 All.book Page 110 Tuesday, June 1, 2004 424 PM Sharp Electronics Schweiz AG