Sherwood R-965 manual Enjoying Surround Sound, Select the desired surround mode

ENJOYING SURROUND SOUND

•Surround sound effect will not work properly if the signal passes through a graphic equalizer.

Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer.

Note: Before surround playback, first perform the SPEAKER SETUP procedure, etc. on the OSD menu for optimum performance. (For details, refer to “SETTING THE SPEAKER SETUP” on page 45.)

Depending on the input digital signal format, select the desired decoding mode.

ENGLISH

1	STANDBY	AUD1		POWER ON
		VID6	7.1IN
		DTS	PL2MV
		DOLBY	PL2MS
	or	PCM	NEO6C
		MPEG	NEO6M
		PAGE2
	PAGE	MAIN		FAV
			CH.
			SET
	VOL			CH/
			ADJUST

MUTE

	DECODE
DSP	DSP
DECODE

Notes :

•Only when the digital input is selected as signal input for the input sources except PHONO, TUNER and TAPE MONITOR, the decoding mode can be selected.

•Noise may be generated at the beginning of playback and while searching during DTS playback in the auto mode. In this case, try playing in the DTS mode.

•You can select the “DTS”, “DOLBY DIGITAL”, “PCM” or “MPEG” mode directly on the remote control.

•Each time the DECODING MODE button is pressed, the decoding mode changes as follows :

*Auto mode(“AUTO” lights up): The input digital signal format (DTS, Dolby Digital, MPEG or PCM( 2 channel stereo), etc.) used by the selected digital input source is detected automatically to perform the necessary decoding process for optimum surround mode.

*Dolby Digital mode(“DOLBY DIGITAL” lights up): The Dolby Digital signal processing is performed only when Dolby Digital signals are input.

*DTS mode(“ DTS” lights up): The DTS signal processing is performed only when DTS signals are input.

*MPEG mode(“MPEG” lights up): The MPEG signal processing is performed only when MPEG signals are input.

*PCM mode(“PCM” lights up): The PCM signal processing is performed only when PCM signals are input.

Select the desired surround mode.

2

•Each time the MULTI CONTROL knob is rotated or the DSP MODE UP(

) or DOWN() button is pressed , the surround mode changes depending on the input signal format and the selected decoding mode as follows :

or

DSP DSP

STANDBY			POWER ON
	AUD1
	VID6	7.1IN
	DTS	PL2MV
	DOLBY	PL2MS
	PCM	NEO6C
	MPEG	NEO6M
	PAGE2
PAGE	MAIN		FAV
		CH.
		SET
VOL			CH/
		ADJUST

MUTE

	DECODE
DSP	DSP

Signal format being input	Selected decoding mode	Selectable surround mode
Dolby Digital 5.1,	Auto, Dolby Digital mode	(DOLBY DIGITAL EX,)
Dolby Digital EX 6.1 channel sources		DOLBY DIGITAL
Dolby Digital 2 channel sources		(DOLBY DIGITAL EX,) DOLBY DIGITAL, PL II MOVIE,
		PL II MUSIC
DTS sources	Auto, DTS mode	(DTS ES MATRIX or DTS ES DISCRETE,) DTS
DTS 96/24 sources		DTS 96/24
MPEG sources	Auto, MPEG mode	MPEG
PCM ( 2 channel ) sources	Auto, PCM mode	PL II MOVIE, PL II MUSIC, BYPASS,
		DTS NEO 6 : CINEMA, DTS NEO 6 : MUSIC, THEATER,
Analog stereo sources	-
		MOVIE, HALL 1/2, STADIUM, CHURCH, CLUB 1/2,
		ARENA 1/2, GAME, 4CH STEREO, MATRIX

( ): Possible only when surround back channel is not set to “None”.(Refer to “When selecting the SPEAKER CONFIGURATION” on page 45.)

BYPASS mode: Audio signals bypass signal processing circuits for surround sound and are played in stereo mode.

If Dolby Pro Logic IIx, Dolby Virtual Speaker or Dolby Headphone mode is combined with BYPASS mode, you will enjoy its original surround effects, not affected by other surround modes.

•You can select the “PL II MOVIE”(or “PL IIx MOVIE”), “PL II MUSIC”(or “PL IIx MUSIC”), “DTS NEO: 6 CINEMA” or “DTS

NEO : 6 MUSIC” mode directly on the remote control depending on the input signal format, the selected decoding mode and the surround back channel setting.

•When MPEG signals are input in the required decoding mode, the corresponding surround mode will be automatically selected

regardless of using the MULTI CONTROL knob or DSP MODE UP() or DOWN() button. Notes:

•When the selected decoding mode is not matched to the input signal format, the indicator of the signal being input flickers, meaning the required process cannot be performed and no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format.

•When the 8 CH DIRECT is selected as an input source, the decoding and surround modes cannot be selected.

•When the pure audio function is activated, the surround mode cannot be selected.

•When 96 kHz PCM signals are input, only the stereo mode can be selected.

•When DTS 96/24 or MPEG signals are input, the Dolby Pro Logic IIx, Dolby Virtual Speaker and Dolby Headphone modes cannot be selected.

30