Setting the CH Level Setup | Sherwood R-965 specs

SETTING THE CH LEVEL SETUP

ENGLISH

C H L E V E L S E T U P

P R E S E T 1 : C AL L

P R E S E T 1

T R I M

P R E S E T 2

: C AL L

P R E S E T 2

T R I M

C H L E V E L T R I M

L F E L E V E L T R I M

, : S e l e c t

R E T U R N : B a c k

E N T E R : C a l l

To recall the channel levels memorized into preset memory or to memorize the channel levels adjusted in the CH LEVEL TRIM menu, etc.

To memorize the adjusted channel levels into preset memory.

To adjust the current channel levels as desired.

To adjust LFE (Low Frequency Effect) levels included in Dolby Digital, DTS and MPEG program sources.

When selecting the PRESET 1 or

PRESET 2

•You can recall the memorized channel levels whenever you want or can memorize the channel levels adjusted in the CH LEVEL TRIM men, etc. into preset memory.

Press the CURSOR UP()/DOWN( )

1 buttons to select the PRESET 1 or PRESET 2 .

PAGE	MAIN	FAV
VOL

1 2 3

4 5 6

7 8 9

0

MI M2 M3

2	Press the CURSOR
	LEFT( )/RIGHT( ) buttons to select
	the desired mode, then press the ENTER

button.

PAGE	MAIN	FAV
VOL

1 2 3

4 5 6

7 8 9

0

MI M2 M3

RNC-510

•Each time these buttons are pressed , the mode changes as follows :

CALL : Select this to recall the channel levels memorized into preset memory .

SAVE : Select this to memorize the channel levels adjusted in the CH LEVEL TRIM menu or in “Adjusting the current channel levels” procedure on page 33.

When selecting the PRESET 1 TRIM or PRESET 2 TRIM

•You can adjust the channel levels directly in the PRESET TRIM menu and can memorize them into preset memory.

Press the CURSOR UP()/DOWN( ) buttons to select the PRESET 1TRIM or PRESET 2 TRIM,

1 then press the ENTER button.

Example) When the PRESET 2 TRIM is selected .

PAGE	MAIN	FAV
VOL

1 2 3

4 5 6

7 8 9

0

	P R E S E T 2	T R I M
F L	: - - - - - -	- - - - - - : 0 dB
F C : - - - - - -		- - - - - - : 0 dB
F R : - - - - - -		- - - - - - : 0 dB
S R : - - - - - -		- - - - - - : 0 dB
B R	: - - - - - -	- - - - - - : 0 dB
B L : - - - - - -		- - - - - - : 0	dB
S L : - - - - - -		- - - - - - : 0	dB
SW : - - - - - -		- - - - - - : 0	dB
R E T U R N : B a c k		, : S e l e c t

MI M2 M3

RNC-510

63

Image 63

Sherwood R-965 manual Setting the CH Level Setup, When selecting the Preset 1 or

Contents

965 Read this Before Operating Your Unit Introduction Safety Instruction Contents System Connections Connecting Antennas Connecting Audio Components Component video input default settings USB audio connection Digital input default settings Connecting 8CH Direct INs Surround back speakers Surround speakers a and B Front left and right speakers and center speaker Speaker placement Room 2 connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel Controls Fluorescent Display Digi Link system remote controls Universal Remote Controls Tape Function Table of the Numbered Buttons Play PLAY/PAUSE AUD1 Loading Batteries Entering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote Controls Operations Listening to a Program SourceBefore operation Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selected Muting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround modes Surround Sound Theater Front L/R Center Enjoying Surround Sound Select the desired surround mode 2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connected Adjusting the current channel levels Adjusting each channel level with test tone Adjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Tuning to preset stations Manual presetting Listening to FM stereo broadcasts Scanning preset stations in sequence Dubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape Monitor Digital Audio Recording with MD Recorder Dolby Digital sources only Operating the sleep timer Adjusting the brightnessOther Functions Compressing the dynamic range Correcting or clearing a label Entering a label Press the Room 2 button Room 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker Setup When selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer Mode Preparations When selecting the Auto Speaker Setup DB , S , 1 0 f t When selecting the Digital Input Setup Setting the System Setup When selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto Display Video When selecting the Component Video Setup When selecting the DC Trigger 2 Setup When selecting the Video 2 OUT When selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to On When selecting the A/V Sync When Decoding Mode is selected Setting the Surround Setup When the Surround Mode is selected When thez Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed Setup When the Room 2 Feed mode is set to On When selecting the Room 2 Feed mode Problem Possible Cause Remedy Troubleshooting Guide Amplifier Section Specifications 965