Adjusting each channel level with test tone | Sherwood R-965

Adjusting each channel level with test tone

•The volume level of each channel can be adjusted easily with the test tone function. Note: When speakers are switched off , the test tone function does not work.

ENGLISH

Enter the test tone mode.

1

STANDBY

POWER ON

AUD2

SLEEP D/A

DIMM S.A/B

ROOM2 SUR.B

T.TON PURE

OSD PARA.

PAGE1

•The test tone will be heard from the speaker of each channel for 2 seconds as follows:

	FL	FC	FR	SR

	Front Left	Center	Front Right	Surround Right
	SUB	SL (	SC)	or (		B L	BR)

SUBwoofer		Surround Left (Surround Center)			(Surr. Back Left		Surr. Back Right)

•Depending on the speaker setting(None or No), the test tone of the corresponding channel is not available.

•( ): possible depending on whether the surround back channel is set to 2 CH or 1 CH.

At each channel, adjust the level as desired

2 until the sound level of each speaker is heard to be equally loud.

PAGE

MAIN

FAV

VOL

CH/

or

ADJUST

		1	2	3
DOWN	UP	4	5	6
DOWN	UP	7	8	9
			0
		MI	M2	M3

• You can select the desired channel and adjust its

level with repeating the steps and in “Adjusting the current channel levels” procedure.

Cancel the test tone function.

3

STANDBY

POWER ON

AUD2

SLEEP D/A

DIMM S.A/B

ROOM2 SUR.B

T.TON PURE

OSD PARA.

PAGE1

Adjusting the current channel levels

•After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit your tastes.

•If you have performed the CH LEVEL SETUP procedure on the OSD menu, you can memorize the adjusted channel levels into preset memory(PRESET 1, PRESET 2) and recall the memorized whenever you want.(Refer to “SETTING THE CH LEVEL SETUP” on page 63.)

1	Select the desired channel.
	• Each time this button is pressed, the corresponding
	channel is selected as follows:
	FRONT-L FRONT-C FRONT-R SURR-R
	SUBWOOFER SURR-L ( SURR-C) or ( BACK-L BACK-R)

PAGE	MAIN	FAV
VOL

or

1 2 3

4 5 6

7 8 9

0

MI M2 M3

CH.

SEL

•Depending on the speaker settings and surround mode, etc., some channels cannot be selected.

•( ): possible depending on whether the surround back channel is set to 2 CH or 1 CH.

Note: When speakers are switched off, only FRONT-L and FRONT-R channels can be selected.

33

Image 33

Sherwood R-965 manual Adjusting each channel level with test tone, Adjusting the current channel levels

Contents

965 Read this Before Operating Your Unit Introduction Safety Instruction Contents System Connections Connecting Antennas Connecting Audio Components Component video input default settings USB audio connection Digital input default settings Connecting 8CH Direct INs Surround back speakers Surround speakers a and B Front left and right speakers and center speaker Speaker placement Room 2 connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting PC for Upgrades Dolby PL II Music Parameter Front Panel Controls Fluorescent Display Digi Link system remote controls Universal Remote Controls Tape Function Table of the Numbered Buttons Play PLAY/PAUSE AUD1 Loading Batteries Entering a Setup Code Enter the 3 digit setup code aiming Remote Control Operation Range Room 2 Remote Controls Operations Listening to a Program SourceBefore operation Adjusting the tone bass and treble When CD, AUX or Video 1~ Video 6 is selected Muting the sound Listening with the headphones Achieving higher purity of sound qualityCompensating for edgy or shrill movie sound tracks Surround modes Surround Sound Theater Front L/R Center Enjoying Surround Sound Select the desired surround mode 2CH downmix mode To listen in a Dolby Pro Logic IIx modeTo listen in a Dolby Virtual Speaker mode To listen in a Dolby Headphone mode Selecting the surround back channel mode as connected Adjusting the current channel levels Adjusting each channel level with test tone Adjust the level of the selected channel as Desired Auto tuning Manual tuningAuto presetting Tuning to preset stations Manual presetting Listening to FM stereo broadcasts Scanning preset stations in sequence Recording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components onto Digital Audio Recording with MD Recorder Other Functions Operating the sleep timer Adjusting the brightnessCompressing the dynamic range Dolby Digital sources only Correcting or clearing a label Entering a label Press the Room 2 button Room 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Power AMP Assign Setting the Power AMP Assign Setting the Speaker SetupWhen selecting the Speaker Configuration Each time these buttons are pressed, and are When selecting the Speaker Distance Virtual Speaker mode changes as follows When selecting the Virtual Speaker Setup When selecting the Subwoofer When selecting the Crossover Frequency When selecting the Subwoofer Mode Preparations When selecting the Auto Speaker Setup DB , S , 1 0 f t When selecting the Digital Input Setup Setting the System Setup When selecting the Tone Control When Cinema EQ mode is selectedWhen Tone Defeat mode is selected When selecting the Current Video When selecting the OSD Auto Display Video When selecting the Component Video Setup When selecting the DC Trigger 2 Setup When selecting the Video 2 OUT When selecting the Digital RE-MASTERING When the DC Trigger 2 mode is set to On When selecting the A/V Sync When Decoding Mode is selected Setting the Surround Setup When the Surround Mode is selected When thez Dolby surround mode is selectedWhen the Dynamic Range is selected When selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dimension control Setting the CH Level Setup When selecting the Preset 1 orWhen selecting the Preset 1 Trim or Preset 2 Trim When selecting the Channel Level Trim When selecting the LFE Level Trim When selecting the Volume Mode Setting the ROOM2 Feed Setup When the Room 2 Feed mode is set to On When selecting the Room 2 Feed mode Problem Possible Cause Remedy Troubleshooting Guide Amplifier Section Specifications 965