Manuals / Siemens / Household Appliance / Air Conditioner

Siemens 125-3208 operating instructions Reset to Factory Defaults, r0000, P0970

Models: 125-3208

1 64

Download 64 pages 51.63 Kb

Page 48

Reset to Factory Defaults

SED2 VFD Electronic Bypass Option Operating Instructions

Reset to Factory Defaults

Parameter	Description			Action	Setting/
Parameter	Description			Action	Default
					Default

P0010	Reset to Factory Default	1.	Press	to enter the SED2	P0010:
P0970		1.	Press	to enter the SED2	Setting = 30
P0970			parameter mode and to display		Setting = 30
	Resets SED2 parameters to the		parameter mode and to display		Default = 0
	factory defaults.		r0000.
	factory defaults.				P0970:
					P0970:
		2.	Press	to advance to	Setting = 1
		2.	Press	to advance to	Default = 0
			parameter P0010.		Default = 0
			parameter P0010.
		3.	Press	to access the
			parameter values level.
		4.	Press	to advance to 30.
		5.	Press	to confirm and save
			the setting.
		6.	Press	to go to parameter
			P0970.
		7.	Press	to access the
			parameter values level.
		8.	Press	to advance to 1.
		9.	Press	to confirm and save
			the setting.

NOTES:

1. First set P0010 = 30.

2. Stop SED2 (that is, disable all pulses) before you reset parameters to factory default values.

3. The following parameters retain their values after a factory reset:

• P0918 (address of CB, communications board or module)

• P2010 (USS baud rate)

• P2011 (USS address)

4. The reset process takes about 10 seconds.

40	Siemens Building Technologies, Inc.

Image 48

Siemens 125-3208 operating instructions Reset to Factory Defaults, r0000, P0970

Contents

SED2 VFD Electronic Bypass Options Operating InstructionsPage SED2 VFD Electronic Bypass Option Operating InstructionsPage Page Page Table of Contents Example SED2 Settings How to Use this Manual Manual OrganizationManual Notations Where To Send Comments Reference DocumentsSafety Instructions Safety InstructionsElectronic Bypass Option Overview General DescriptionController Board CONTROLLER BOARDVFD0095R1 Figure 3. Controller Board Inputs and OutputsContactors Keypad Functions2-CONTACTORKEYPAD 3-CONTACTORKEYPADPushbutton/Indicator DescriptionOutput relay on the Controller board Installation Instructions Mechanical InstallationDimensions and Weights Environmental ConditionsMounting Frame Size A and BFrame Size CDimensions in Inches Centimeters Figure 7. Frame Sizes D and E Conduit LocationsViewed from Bottom Figure 6. Frame Sizes A through C ConduitElectrical Installation P0748 = Digital Out 1 Reverse Figure 10. Routing of Power and Control Wiring Figure 11. Routing of Power and ControlWiring for Frame Sizes C, D, and E for Frame Sizes A and BSwitch DisconnectOverload Ground LugDisconnect OverloadGround Lug AmpsWire DisconnectOverload Ground LugWire DisconnectOverload Ground LugStartup Procedures Safety PrecautionsInstallation Inspection Power-OnSwitch DescriptionPosition Quick Commissioning Siemens Building Technologies, IncSetting DefaultUser Access Level ParameterOperation for Europe/N AmericaRated Motor Voltage Rated Motor Power Rated Motor CurrentRated Motor cosPhi P308, or Rated Motor Efficiency P0309Rated Motor Frequency Rated Motor SpeedSelection of Command Source Start CommandMotor Overload Factor Selection of Command Source Start CommandSpeed Command Source Selection of FrequencySpeed Command Source Selection of FrequencySetpoint Minimum Motor FrequencyMaximum Motor Frequency Ramp-upTimeRamp-downtime End Quick CommissioningAdditional Parameter Settings Flying StartFlying Start r0000Motor Current Flying Start r0000Search Rate Flying Start r0000Automatic Restart Automatic Restartr0000 Setting DefaultAutomatic Restart Continued ParameterNumber of Restart Attempts r0000Time to First Restart r0000Vdc Controller Configuration of VdcController Pulse Frequency r0000Motor Data Identification Motor Data Identificationr0000 Motor Data Identification Continued Reset to Factory Defaults Reset to Factory Defaultr0000 P0970Required SED2 Parameter Settings Required SED2 Parameter SettingsApplication Feature Setup OverviewAuto Bypass without Interlock DescriptionSettings Example SED2 SettingsApplication Feature Setup Interlock SettingsDescription Siemens Building Technologies, IncP0700 in000 = Essential Services Wiring Example for InterlockDescription Wiring Example for Essential Services SettingsSiemens Building Technologies, Inc Interlock and Auto Bypass on VFD Fault SettingsDescription Technical Specifications SpecificationsDrive Specifications Table 5. Electronic Bypass SpecificationsTable 6. SED2 Specifications Continued Drive SpecificationsSED2 VFD Electronic Bypass Operating Instructons DescriptionTroubleshooting Power-onInitialization FailureUnit Fault Condition Override Jumper FusesTable 8. Fuse Replacement Information Bypass Option Part NumberPrimary Fuse F3 and F4 Secondary Fuse F2VFD0122R2 Figure 15. Controller Board Inputs and OutputsTroubleshooting Siemens Building Technologies, IncSiemens Building Technologies, Inc