TCP/IP Commands | Silex technology SX-550 guide

Command

Description

3Text to PostScript

4PostScript Tagged Binary

5DC1 Special

TCP/IP Commands

	Table 44 TCP/IP Commands

Command	Description

SET IP ACcess	Allows or prevents access to a block of remote addresses
	The default value is empty list.
	Sample output:
	SET IP ACcess [EN DI ALL] aa.bb.cc.dd {MAsk
	ee.ff.gg.hh]
SET IP RANge	Allows or prevents access to a range of remote addresses
	The default value is empty list.
	Sample output:
	SET IP RANge [EN DI ALL] aa.bb.cc.dd {MAx
	ee.ff.gg.hh]
SH IP ACcess	Displays current access list settings
	Sample output:
	All hosts permitted access
SET IP ADdress	Sets server IP address
	The default value is 192.0.0.192
	Sample output:
	SET IP ADdress aa.bb.cc.dd
SET IP ARP	Enables or disables setting of IP address with an ARP packet
ENable	The default value is Enable.
	Sample output:
	SET ARP [ENable DIsable]
SET IP BAnner	Enables or disables printing of job banner on LPD jobs
	The default value is Disable.
	Sample output:
	SET IP BAnner [ENable DIsable]
SET IP CHKSUM	Enables or disables verification of IP checksum on received packets
	The default value is Enable.
	Sample output:
	SET IP CHKSUM [ENable DIsable]
SET IP BOot	Sets number of tries for each enabled IP boot method, if not set to static


Page 68	silex	Console Commands
	Part Number 40183-101

Image 74

Silex technology SX-550 manual TCP/IP Commands Description

Contents

Developer’s Reference Guide Trademarks Contents Configuring Serial Port Monitor Alert and Trap Configuration Figures Silex Contents Part Number Emissions Disclaimer Safety PrecautionsAbout This Reference Guide Silex About This Reference Guide Part Number Processor and Wireless LAN Radio PCB Introduction Silex Introduction Part Number Installing Wlan Module in Daughtercard Chapter Getting Started Verify Development Kit Contents Installing the SX-550 Wlan Module Wlan Module Inserted in Daughtercard SX-550 Evaluation Daughtercard Monitoring Module Status Status Monitors Function State Function State Status OEM Interface Pinout SignalOEM Interface OEM Interface Signal Description Pin Type Power Management Electrical CharacteristicsPower Input Serial Peripheral Interface Logical Serial Port Signal Descriptions Pin Input/Output Serial Ports Ground General Purpose IO Signal Descriptions Pin Selectable General Purpose IO LED and Gpio Descriptions LEDs and General Purpose IO SignalsEvaluation CN210 Drive High/Low Description Daughtercard GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 Additional OEM Interface Signals RS-232 Cable OEM Interface Electrical Characteristics UART0TXD, UART0RTS UART1TXD, UART1RTS Evaluation Module Connections Chapter Using the SX-550 Wlan ModuleUsing the Wireless Method Port Settings Parameter Access silex Console InterfaceUsing the Wired Ethernet Method Action Result Generating Configuration DataPushbutton Functions Silex Using the SX-550 Wlan Module Part Number Chapter Accessing Configuration Parameters Access ExtendView Utility Installing ExtendView Utility Using ExtendView Utility ExtendView Main Create View with Default Settings Access Http Pages ExtendView Configuration Window Access Internal Command Console SX-550 Home Telnet Where x.x.x.x is the IP address of the SX-550 module Using Telnet SessionUsing Terminal Emulator through the Serial Port Using AT Modem Commands Standard AT Commands Supported AT Commands Parameter Description Response Codes Parameter Command DescriptionExtended AT Commands Parameter Description AT#Cset nw ssid silex#Csave Factory Default Settings Parameter Description Chapter Setting Configuration ParametersFactory Default Settings CTS/RTS Changing Serial Settings Modify Basic SettingsRestoring Factory Default Settings Parameter Description Settings Default Setting Serial Setting Parameters Parameter Setting Modifying TCP/IP Settings TCP/IP Window TCP/IP Settings Change Password Window TCP/IP Configuration Settings Parameter DNS Command Description Configure Simple Network Management ProtocolSnmp Commands Configuring Gpio Alerts and Traps Snmp Trap Settings Parameter SET Gpio DIR in OUT Gpio # Gpio Commands DescriptionShow Gpio DIR SET Gpio Special ENA/DIS Gpio Trigger Commands DescriptionShow Gpio Special Trig # Email String Your email text msg here Gpio #2 is Gpio Transmit Commands DescriptionTrig # Email String Gpio #1 is Gpio #2 is Index # Monitor String Port Monitor Alert Commands DescriptionShow Port S1 Trigmon Index # Xmit String Trigmon Commands DescriptionShow Port S1 Trigxmt Index # Xmit String Trigger string was seen OEM Header Interface OEM Header Interface Pinout SignalDesigning with the SX-550 Differential Output Ethernet Transmit Data primary Antenna Connectors Transformer Specification Ethernet PHY YCL General Purpose I/O Interface10/100M Magnetics Manufacturers Part Number GTS Power 40-Pin Drive High/Low Description Component Specifications Chapter Product SpecificationsProduct Specifications Radio Performance Specifications Parameter Parameter Specifications TKIP, AES Receiver Sensitivity Production Specification Port Destination Device TCP Port ConnectionsTCP Port Connections Network Commands Description Appendix a Console CommandsWireless and Network Security Commands SET NW AUTHtype Open Shared Ttls Leap WPA-PSK SET NW ENC SET NW KEY# SET NW RTS Common name SET NW CertcnName User defined SET NW CERTCN2 SET NW ID SET NW CertexpSET NW Certkey SET NW PW SET NW Wpagroup Enable Disable XON/XOFF RS232 Port CommandsPort Commands Description CL Port S1 JOB SET Port S1 Stop 1 Server Information CommandsServer Information Commands Description Sample Output SET Snmp Getcomm Serial server Firmware Ver .19 Boot Ver 16Mbit Flash Command Description Sample OutputSnmp is Enabled SET Snmp LOCation string Service Commands Service Commands Description SET Servi service name IP ENable DIsable SET Servi service name FRMSET Servi service name FRS SET Servi service name NAme Newname Enter LANGUAGE= String CommandsString Commands Description POSTSCRIPT\0A TCP/IP Commands TCP/IP Commands Description SET IP Http Auto Bootp Rarp Dhcp StaticSET IP FTP SET IP LPD SET IP TCP SET IP Tftp Power Configuration Command Description Power Configuration CommandsFirmware Update Firmware Update Command Description SET LOAd HOst Name SET LOAd ENable DIsableFirmware load is disabled SET LOAd IP Aa.bb.cc.dd Miscellaneous Commands Miscellaneous CommandsHelp Commands Antenna Cable Assembly Appendix B Engineering Drawings Electrical Specifications for Antenna Electrical Specifications Parameter Value Vswr Silex technology america, Inc