![](/images/new-backgrounds/1054917/5491713x1.webp)
Attaching a button
Flat buttons can be sewn on quickly and easily using the plain
Recommended settings
Stitch Selection:
Needle Position :
Stitch Width: To suit Button
Foot: Button Sewing (H)
Needle Plate : General Purpose (A)
Attach Feed Cover (F)
Note: Before you can attach a button, the bobbin thread must be brought up through the hole in the feed cover.
1.Set stitch width at ( | ), and needle position | |
selector at ( | ). Position button under foot |
and lower the needle into the center of the left hole. Lower the foot. Turn hand wheel toward you until needle rises out of button and is above the foot.
2.Move stitch width selector until needles is over the other hole in the button. Then, when you begin to stitch, the needle should enter into the right hole of the button. Take six or more
3.To fasten stitching, adjust width to ( ) and take three or four stitches. Remove work, draw threads to underside, fasten, and trim.
84
Pegado de botones
Los botones planos pueden coserse con rapidez y facilidad, utilizando el punto de zig- zag plano. El prensatelas especial para coser botones (H) puede adquirirlo en su centro de costura.
Posiciones recomendadas
Selección punto: Punto
Posición aguja:
Anchura punto: Apropiada al botón
Prensatelas: Para coser botones (H)
Plancha aguja: Uso general (A) Colocar Plancha Cubre Arrastre (F)
Nota: Antes de pegar un botón, el hilo de la bobina debe sacarse por el agujero de la plancha cubre arrastre.
1. Coloque el ancho del punto en ( | ) y el |
selector de posición de aguja en ( | ). |
Colocar el botón debajo del prensatelas y bajar la aguja dentro del centro del agujero izquierdo. Bajar el prensatelas. Gire el volante hacia Vd. hasta que la aguja salga del botón y esté por encima del prensatelas.
2.Mueva el selector de anchura hasta que la aguja esté sobre el otro agujero del botón. Entonces, cuando empiece a coser, la aguja debería entrar dentro del agujero derecho del botón. De seis o más puntos en
3. Para assegurar el punto, ajuste la anchura a
( ), y de tres o cuatro puntadas. Quite la labor, lleve los hilos hacia la parte posterior, anúdelos y corte.
|
|
|
| 4 | 2 |
|
|
|
|
| |
|
| 8 |
|
| 1 |
|
| 9 |
|
| |
| 7 |
|
|
| |
|
|
|
|
| |
| 10 |
|
|
|
|
|
|
|
|
| 21 |
11 |
|
|
|
| 3 |
|
|
|
|
| 5 |
12 |
|
|
|
| 6 |
|
|
|
| 19 | |
30 |
|
|
|
| |
|
|
|
|
| |
15 | 13 | 17 |
|
| 20 |
|
|
|
| ||
|
|
|
|
| |
14 |
|
|
|
|
|
| 18 |
|
|
|
|
|
|
|
|
| 29 |
|
|
|
|
| 28 |
|
|
|
|
| 27 |
22 |
|
|
|
|
|
|
| 24 |
|
|
|
23 |
|
|
|
|
|
16 |
|
| 25 |
| 26 |
|
|
|
|
| |
|
|
|
|
| P/N 362095 |
|
|
|
|
| 5 |