Sony DSR-DR1000 manual 34

When controlling this unit from an editing control unit				Video input signal	Corresponding	Lit indicator
connected to the REMOTE IN (R)connector, see “Control				(input connector)	INPUT	in the INPUT
mode selector” on page 15 and the description of the					SELECT	signal display
REMOTE I/F menu item on page 72.					button	section
1 Power on the video monitor, then set its input				SDI signal	VIDEO	SDI in VIDEO
				(SDI IN)		group
	switches according to the signals input from the
				i.LINK-compatible	VIDEO	i.LINK
	player.			digital video signal in
2 Set up the player to play back a tape.				DV format
				( S400(i.LINK))
	For details, refer to the operating instructions for the			Internal test video	VIDEO	SG in VIDEO
				signal		group
	player.
3 Power on this unit by pressing the 1 switch on the
				Audio input signal	Corresponding	Lit indicator
				(input connector)	INPUT SELECT	in the INPUT
	front panel.				button	signal display
4 When the REMOTE indicator is off (the external						section
				Analog signal	CH1 1/2 and	ANALOG in
	editing control unit is not used), use the COUNTER			(AUDIO IN 1/3 and	CH2 3/4	AUDIO group
	SELECT button to select the type of time data to be			AUDIO IN 2/4)
	used.
				AES/EBU signal	CH1 1/2 and	AES/EBU in
	Each press of this button cycles through three options:			(AUDIO (AES/EBU)	CH2 3/4	AUDIO group
				IN)
	COUNTER (CNT value), TC (time code), and U-BIT
				SDI signal	CH1 1/2 and	SDI in AUDIO
	(user bit data). The time data type indicator for each
				(SDI IN)	CH2 3/4	group
	option lights as it is selected.
				i.LINK-compatible	automatic	i.LINK
				digital audio signal in	setting
	Selected time data	Time data type indicator
				DV format	depending on
	Count value of the time	COUNTER		( S400(i.LINK))	video input
	counter				signals
	Time code	TC		Internal test audio	CH1 1/2 and	SG in AUDIO
				signal	CH2 3/4	group
	User bit data	U-BIT
	When the REMOTE indicator is lit, selection of the
				Caution
	time data type is carried out at the editing control unit.			Once you have started recording, you cannot change
5 Select the formats of video and audio input signal to				the input signal selection.
			6 Select the audio mode.
	be recorded.
	Use the INPUT SELECT buttons in the video/audio			Select either two-channel mode (2 CHANNEL) or
	input setting section to select the desired signal
	formats. Each selection is shown by a lit indicator in			four-channel mode (4 CHANNEL) with the REC
	the INPUT signal display section.			MODE menu item (see page 71). The corresponding
				indicator lights in the REC MODE display.

Video input signal	Corresponding	Lit indicator
(input connector)	INPUT	in the INPUT
	SELECT	signal display
	button	section
Composite signal	VIDEO	COMPOSITE
(VIDEO IN: Y/CPST)		in VIDEO
		group
Separated Y/C	VIDEO	S VIDEO in
signal		VIDEO group
(VIDEO IN: Y/CPST
and R−Y/S−C)
Component signal	VIDEO	Y−R,B in
(VIDEO IN: Y/CPST,		VIDEO group
R−Y/S−C, and B−Y/
S−Y)

Audio mode	Lit indicator in the REC MODE
	display
2-channel mode	2CH
4-channel mode	4CH

Cautions

•Two audio recording modes, with either two channels at 48 kHz or four channels at 32 kHz, can be used on this unit. It is not possible to select any other mode (for example with four channels at 48 kHz).

•If there is a point where the audio mode is switched, it is not possible to carry out insert editing over a section including that point.

34 Recording