Sony DSR-DR1000 manual 69

TIME CODE [Time code]: Settings related to the time code	Description of settings
generator
VITC POS SEL-1 [> VITC pos-1]: Select a line to insert the	(For DR1000)
VITC in.	20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
	from 12 to 20.
Note
	Factory default setting: 16 LINE [>> 16 line]
You can insert the VITC signal in two places. To insert it in two
	(For DR1000P)
places, set both this item and also VITC POS SEL-2.
	22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line
	from 9 to 22.
	Factory default setting: 19 LINE [>> 19 line]
VITC POS SEL-2 [> VITC pos-2]: Select a line to insert the	(For DR1000)
VITC in.	20 LINE [>> 20 line] to 12 LINE [>> 12 line]: Select any line
	from 12 to 20.
Note
	Factory default setting: 18 LINE [>> 18 line]
You can insert the VITC signal in two places. To insert it in two
	(For DR1000P)
places, set both this item and also VITC POS SEL-1.
	22 LINE [>> 22 line] to 9 LINE [>> 9 line]: Select any line
	from 9 to 22.
	Factory default setting: 21 LINE [>> 21 line]
VITC OUTPUT [> VITC out]: Select the time code to be output	OFF [>> OFF]: Do not output VITC.
as VITC.	TC [>> TC]: Output TC after converting it into VITC.
	*VITC [>> VITC]: Output VITC.
EE OUT PHASE [> EE out]: Determine the output phase for	*MUTE [>> mute]: Mute the output.
the LTC signal output from the TIME CODE OUT	THROUGH [>> through]: Output the time code input to the
connector when recording time code and in STOP REC	TIME CODE IN connector as it is. (See example
mode (forced EE mode).	configuration on page 74.)
	VIDEO INPUT PHASE [>> V input]: Output the time code
	with the same phase as the input video signal phase.
	(See example configuration on page 74.)
	VIDEO OUTPUT PHASE [>> V output]: Output the time code
	with the same phase as the output video signal phase.
	(See example configuration on page 75.)
MUTE IN SRCH [> Mute in SR]: Select whether to mute the	OFF [>> OFF]: Do not mute.
output from the TC OUT connector in search (jog/shuttle)	*ON [>> ON]: Mute.
mode.
VIDEO CONTROL [Video]: Settings related to video control	Description of settings
INT VIDEO SG [> Video SG]: Select the test signal to be	(For DSR-DR1000)
output from the internal test signal generator. When SG is	*75% COLOR BARS [>> 75% bars]: 75% color bar signal
selected using the VIDEO button in the video/audio input	BLACK BURST [>> BB]: Black burst signal
setting section, the internal test signal generator outputs
	(For DSR-DR1000P)
the selected test signal. This signal can be recorded.
	*100% COLOR BARS [>> 100% bars]: 100% color bar signal
	75% COLOR BARS [>> 75% bars]: 75% color bar signal
	BLACK BURST [>> BB]: Black burst signal
STD/NON-STD [> STD/N-STD]: Select the STD or NON-STD	*FORCED STD [>> STD]: The STD mode is always used
mode in accordance with the composite video or S-video	(forced STD mode).
input.	FORCED NON-STD [>> NON-STD]: Use this setting when
	the input video signal is unstable (forced NON-STD
	mode).
OUT REF SEL [> Out Ref]: Select the reference video signal	*REF VIDEO [>> REF]: Use the signal input to a REF. VIDEO
to use.	IN connector as the reference video signal. The input
	video signal to be edited is required to be in
	synchronization with the reference video signal.
	INPUT VIDEO [>> INPUT]: Use the input video signal
	selected with the VIDEO button in the video/audio input
	setting section.
(For DSR-DR1000 only)	*OFF [>> OFF]: Do not remove black setup.
SETUP REMOVE [> Setup rmv]: Determine whether or not to	ON (REMOVE) [>> ON]: Remove black setup.
remove black setup (7.5 IRE) from input analog video
signals when converting them into digital signals.

Menu Contents 69