If such an alarm message appears, a connection or operation error may have been made, or condensation on heads may have occurred. Follow the direction indicated on the monitor screen.
Note
To display alarm messages on the monitor screen, it is necessary for the monitor to be connected to the SUPER connector, and set the following menu items to ON.
•CHARA. DISPLAY (see page 66)
•ALARM (see page 67)
•REF ALARM (see page 67)
Alarm messages and associated directions
Alarm message on monitor screen | Direction | Alarm message in time |
(Cause) |
| counter display |
|
|
|
A | Use a standard signal. | VIN |
input video. |
|
|
|
|
|
A | Use a standard signal. | REF |
for REF. VIDEO. |
|
|
|
|
|
Abnormal settings selected in setup | Correct the setup menu settings. Contact your Sony | ILL. SETUP! |
menu. | dealer if this alarm message appears again after |
|
| making corrections. |
|
|
|
|
Audio mixing mode cannot be changed | – | REC mode! |
during recording. |
|
|
|
|
|
Audio REC (recording) mode cannot be | – | REC mode! |
changed during recording. |
|
|
|
|
|
Counter mode is selected. | Use the COUNTER SELECT button to light the TC or | CNT mode! |
|
| |
|
|
|
Input selection cannot be changed in | – | REC mode! |
REC (recording) mode. |
|
|
|
|
|
Input signal does not conform to | – | Unknown Sig |
DVCAM/DV format. |
|
|
|
|
|
Input signal is 625/50. (For DSR- | – | 625/50 sig! (For DSR- |
DR1000) |
| DR1000) |
|
|
|
Input signal is 525/60. (For DSR- | – | 525/60 sig! (For DSR- |
DR1000P) |
| DR1000P) |
|
|
|
Input video is not detected. | Check the VIDEO indicator in the INPUT signal | No INPUT! |
| display section and supply an appropriate video |
|
| signal. |
|
|
|
|
Input video signal does not synchronize | Use a reference video signal. | ILL. REF! |
with REF. VIDEO signal. |
|
|
|
|
|
Invalid subclip. | There is an invalid subclip setting, for example a Mark | CLIP set ! |
| Out point before a Mark In point. Correct the setting. |
|
|
|
|
MODE CANNOT BE CHANGED | To exit simultaneous recording and playback mode, | Dual REC ! |
DURING DUAL RECORDING. | press the R button in the PANEL SELECT section to |
|
| stop recording and then press the R button again so |
|
| that the button goes out. |
|
|
|
|
Moisture has been detected. | Keep the power on and wait until this alarm message | HUMID! |
| disappears. |
|
|
|
|
Rec inhibit mode is selected. | Set the REC INHIBIT menu item (see page 65) to | REC INHI.! |
| OFF. |
|
|
|
|
Remote mode is selected. | Set the LOCAL/REMOTE switch to LOCAL. | REMOTE! |
|
|
|
Simultaneous recording and playback. | Stop the unit by pressing the STOP button and then | Dual Rec ! |
| switch with the buttons in the PANEL SELECT |
|
| section. |
|
|
|
|
TC EXTERNAL is selected. | Set the TC MODE menu item (see page 68) to INT | TC EXT! |
| PRESET. |
|
|
|
|
TCG REGEN mode is selected. | Set the TC MODE menu item (see page 68) to INT | REGEN mode! |
| PRESET. |
|
|
|
|
98 Troubleshooting