Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 SSPET5 4.5. Initial conveying operations, Putting into operation

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 33

Image 33

SSPET5

4.5. Initial conveying operations

Metal shavings may be inside the pipe from cutting down pipes into lengths. The- se are pulled during the first conveying process and collected in the separator.

This material should not be used again.

4.6. Alarm Messages displayed on the controller SSE

If a disturbance occurs in the unit, an alarm message will be issued (option, only if the alarm indicating device has been activated).

An “E” appears in the display and an error number.

The alarm indicating device (signal siren, horn) reacts.

The control system can only restart operation when the mal- function has been corrected.

Press the “acknowledgement key”.

SM4-630

The cause of the malfunction will not be corrected by pres- sing the “acknowledgement key”.

Putting into operation 32

Page 33

Image 33

Sterling SSPET 5 SSPET5 4.5. Initial conveying operations, Alarm Messages displayed on the controller SSE

Contents

Sterling Material Processing Operating Instructions Single Conveyor Unit For Powder SSPETSM4-630 Sales and Contracting Department Parts and Service DepartmentSSPET5 Sterling Material Processing Technical serviceTelephone 800 Edition 02/01 Sterling order confirmation no SM4-630SSPET5 1. Safety instructions Table of contents2. Assembly instructions 3. Functional description6. Technical data 7. Parts list 8. Accessories SSPET5 5. Maintenance1. Safety instructions Safety instructionsSSPET5 Safety instructions SSPET5 1.1. Warnings and symbols∙ ∙ ∙ ∙ ∙ ∙ SSPET5 1.2. Explanations and informationSafety instructions SSPET5 1.3. For your safety Safety instructionsThis avoids injury and damage to equipment SSPET5 Safety instructions∙ ∙ ∙ ∙ Safety instructionsSSPET5 SSPET5 1.4. For the operating safety of the equipment 2. Assembly instructions Assembly instructionsSSPET5 SSPET5 2.1. Assembly The equipment is delivered as a complete assemblyAssembly instructions Assembly instructions Assembly SM4-630SSPET5 SSPET5 2.2. Mounting the suction pipe MV Assembly instructionsConnect the inner pipe with the straight end to a flexible hose SSPET5 2.3. Electrical connection Assembly instructionsThe operating voltage is 230 V/50 Hz Special voltages on request 2.3.2. Installation of the signal line of the SKW optional SSPET5 2.3.1. Installation of the “flap switch” signal lineInsert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller Assembly instructionsAssembly instructions SSPET5This work must be carried out by qualified personnel only SSPET5 2.4. Compressed-air supply For operating the cleaning unit, a compressed-air supply is necessaryAssembly instructions 3. Functional description Functional descriptionSSPET5 SSPET5 3.1. General The filter-cleaning process takes place during the conveying processFunctional description SSPET5 3.2. Controller SSE The emptying time consists of 8 secondsFunctional description An “E” appears in the display and an error number SSPET5Functional description Functional description SSPET5 3.3. Controller SSP4. Putting into operation Putting into operationSSPET5 SSPET5 4.1. Checking the pipe system Remove the flexible hose from the connected material takeupPutting into operation If the conditions points 3 + 4 are not met SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are met Putting into operationSetting the conveying time SSPET5 4.3. Setting the controller SSEThe turbine is running but no material is being conveyed The conveying capacity is too lowthe “change-over” key SSPET5 Setting the line clear timeIf no line clear valve has been installed enter “0 Press the “arrow key” andSetting the pulse duration Press the “arrow key” SSPET5 4.4. Setting the controller SSPSetting the time interval the “change-over” key4.6. Alarm Messages displayed on the controller SSE SSPET5 4.5. Initial conveying operationsPutting into operation The following error messages can be displayed SSPET5Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP 4.8. Switching off the unitPutting into operation 5. Maintenance MaintenanceSSPET5 Please observe the maintenance intervals MaintenanceSSPET5 SSPET5 5.1. Maintenance intervals MaintenanceDaily 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unit SSPET5 5.2. Servicing the conveyorMaintenance Removal InstallationMaintenance SSPET5Maintenance SSPET5 5.2.2. Changing the sealing ring of the outlet flapAssembly sealing ring SM4-630Maintenance SSPET5 5.2.3. Adjusting the flap switchSSPET5 5.3. Replacing carbon brushes at turbine MaintenanceSSPET5 SM4-630 Maintenance SSPET5 InstallationOptional Features 6. Technical dataTechnical data Basic VersionSSPET5 Dimension Sheet Technical dataSM4-630 Parts list 7. Parts listThis parts list is only for the use of trained personnel only SSPET5SSPET5 SSPET5 Parts listSM4-630 Designation Order noParts list SSPET5Accessories 8. AccessoriesSSPET5 SM4-630