Manuals
/
Sterling
/
Marine Equipment
/
Marine Battery
Sterling
SSPET 5 operating instructions SSPET5 SSPET5, Parts list, SM4-630
Models:
SSPET 5
1
48
50
50
Download
50 pages
3.15 Kb
43
44
45
46
47
48
49
50
<
>
Install
Parts list
Error codes
Dimension
Maintenance
Assembly instructions
An “E” appears in the display and an error number
SSPET5 4.2. Adjusting the suction pipes
SSPET5 4.3. Setting the controller SSE
For operating the cleaning unit, a compressed-air supply is necessary
Page 48
Image 48
SSPET5
SSPET5
SM4-630
Parts list 47
Page 47
Page 49
Page 48
Image 48
Page 47
Page 49
Contents
Sterling Material Processing
Operating Instructions Single Conveyor Unit For Powder SSPET
SM4-630
Parts and Service Department
Sales and Contracting Department
Technical service
SSPET5 Sterling Material Processing
Telephone 800 Edition 02/01 Sterling order confirmation no
SM4-630
SSPET5
Table of contents
1. Safety instructions
2. Assembly instructions
3. Functional description
SSPET5 5. Maintenance
6. Technical data 7. Parts list 8. Accessories
1. Safety instructions
Safety instructions
SSPET5
SSPET5 1.1. Warnings and symbols
Safety instructions
∙ ∙ ∙ ∙ ∙ ∙
SSPET5 1.2. Explanations and information
Safety instructions
SSPET5 1.3. For your safety
Safety instructions
This avoids injury and damage to equipment
Safety instructions
SSPET5
∙ ∙ ∙ ∙
Safety instructions
SSPET5
SSPET5 1.4. For the operating safety of the equipment
2. Assembly instructions
Assembly instructions
SSPET5
SSPET5 2.1. Assembly
The equipment is delivered as a complete assembly
Assembly instructions
Assembly instructions
Assembly SM4-630
SSPET5
SSPET5 2.2. Mounting the suction pipe MV
Assembly instructions
Connect the inner pipe with the straight end to a flexible hose
SSPET5 2.3. Electrical connection
Assembly instructions
The operating voltage is 230 V/50 Hz Special voltages on request
SSPET5 2.3.1. Installation of the “flap switch” signal line
2.3.2. Installation of the signal line of the SKW optional
Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller
Assembly instructions
Assembly instructions
SSPET5
This work must be carried out by qualified personnel only
SSPET5 2.4. Compressed-air supply
For operating the cleaning unit, a compressed-air supply is necessary
Assembly instructions
3. Functional description
Functional description
SSPET5
SSPET5 3.1. General
The filter-cleaning process takes place during the conveying process
Functional description
SSPET5 3.2. Controller SSE
The emptying time consists of 8 seconds
Functional description
An “E” appears in the display and an error number
SSPET5
Functional description
SSPET5 3.3. Controller SSP
Functional description
4. Putting into operation
Putting into operation
SSPET5
SSPET5 4.1. Checking the pipe system
Remove the flexible hose from the connected material takeup
Putting into operation
SSPET5 4.2. Adjusting the suction pipes
If the conditions points 3 + 4 are not met
If the conditions points 3 + 4 are met
Putting into operation
SSPET5 4.3. Setting the controller SSE
Setting the conveying time
The turbine is running but no material is being conveyed
The conveying capacity is too low
SSPET5 Setting the line clear time
the “change-over” key
If no line clear valve has been installed enter “0
Press the “arrow key” and
SSPET5 4.4. Setting the controller SSP
Setting the pulse duration Press the “arrow key”
Setting the time interval
the “change-over” key
4.6. Alarm Messages displayed on the controller SSE
SSPET5 4.5. Initial conveying operations
Putting into operation
The following error messages can be displayed
SSPET5
Putting into operation
SSPET5 4.7. Alarm Messages displayed on the controller SSP
4.8. Switching off the unit
Putting into operation
5. Maintenance
Maintenance
SSPET5
Please observe the maintenance intervals
Maintenance
SSPET5
SSPET5 5.1. Maintenance intervals
Maintenance
Daily
5.2.1. Cleaning/replacing the filter cartridges of the cleaning unit
SSPET5 5.2. Servicing the conveyor
Maintenance
Installation
Removal
Maintenance
SSPET5
SSPET5 5.2.2. Changing the sealing ring of the outlet flap
Maintenance
Assembly sealing ring
SM4-630
SSPET5 5.2.3. Adjusting the flap switch
Maintenance
SSPET5 5.3. Replacing carbon brushes at turbine
Maintenance
SSPET5 SM4-630
SSPET5 Installation
Maintenance
6. Technical data
Optional Features
Technical data
Basic Version
SSPET5 Dimension Sheet
Technical data
SM4-630
7. Parts list
Parts list
This parts list is only for the use of trained personnel only
SSPET5
SSPET5 SSPET5
Parts list
SM4-630
Order no
Designation
Parts list
SSPET5
8. Accessories
Accessories
SSPET5
SM4-630