Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 SSPET5 4.3. Setting the controller SSE, Setting the conveying time

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 30

SSPET5

SSPET5

4.3. Setting the controller SSE

F

&

The filling capacity of the hopper loader may not exceed the material inlet.

The setting is independent of the conveying line and the ma- terial to be conveyed.

It is only possible to set the conveying time / line clear time when the unit is not conveying any material.

Setting the conveying time

Press the “arrow key”.

&

The conveying time which was last selected appears in the display.

1-99 seconds may be set for the conveying time.

The turbine is running but no material is being conveyed:

Reduce the conveying time.

The conveying capacity is too low:

Increase the conveying time.

SM4-630

Putting into operation 29

Image 30

Sterling SSPET 5 SSPET5 4.3. Setting the controller SSE, Setting the conveying time, The conveying capacity is too low

Contents

Sterling Material Processing Operating Instructions Single Conveyor Unit For Powder SSPETSM4-630 Parts and Service Department Sales and Contracting DepartmentTelephone 800 Edition 02/01 Sterling order confirmation no Technical serviceSSPET5 Sterling Material Processing SM4-630SSPET5 2. Assembly instructions Table of contents1. Safety instructions 3. Functional descriptionSSPET5 5. Maintenance 6. Technical data 7. Parts list 8. Accessories1. Safety instructions Safety instructionsSSPET5 SSPET5 1.1. Warnings and symbols Safety instructions∙ ∙ ∙ ∙ ∙ ∙ SSPET5 1.2. Explanations and informationSafety instructions SSPET5 1.3. For your safety Safety instructionsThis avoids injury and damage to equipment Safety instructions SSPET5∙ ∙ ∙ ∙ Safety instructionsSSPET5 SSPET5 1.4. For the operating safety of the equipment 2. Assembly instructions Assembly instructionsSSPET5 SSPET5 2.1. Assembly The equipment is delivered as a complete assemblyAssembly instructions Assembly instructions Assembly SM4-630SSPET5 SSPET5 2.2. Mounting the suction pipe MV Assembly instructionsConnect the inner pipe with the straight end to a flexible hose SSPET5 2.3. Electrical connection Assembly instructionsThe operating voltage is 230 V/50 Hz Special voltages on request Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller SSPET5 2.3.1. Installation of the “flap switch” signal line2.3.2. Installation of the signal line of the SKW optional Assembly instructionsAssembly instructions SSPET5This work must be carried out by qualified personnel only SSPET5 2.4. Compressed-air supply For operating the cleaning unit, a compressed-air supply is necessaryAssembly instructions 3. Functional description Functional descriptionSSPET5 SSPET5 3.1. General The filter-cleaning process takes place during the conveying processFunctional description SSPET5 3.2. Controller SSE The emptying time consists of 8 secondsFunctional description An “E” appears in the display and an error number SSPET5Functional description SSPET5 3.3. Controller SSP Functional description4. Putting into operation Putting into operationSSPET5 SSPET5 4.1. Checking the pipe system Remove the flexible hose from the connected material takeupPutting into operation If the conditions points 3 + 4 are met SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are not met Putting into operationThe turbine is running but no material is being conveyed SSPET5 4.3. Setting the controller SSESetting the conveying time The conveying capacity is too lowIf no line clear valve has been installed enter “0 SSPET5 Setting the line clear timethe “change-over” key Press the “arrow key” andSetting the time interval SSPET5 4.4. Setting the controller SSPSetting the pulse duration Press the “arrow key” the “change-over” key4.6. Alarm Messages displayed on the controller SSE SSPET5 4.5. Initial conveying operationsPutting into operation The following error messages can be displayed SSPET5Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP 4.8. Switching off the unitPutting into operation 5. Maintenance MaintenanceSSPET5 Please observe the maintenance intervals MaintenanceSSPET5 SSPET5 5.1. Maintenance intervals MaintenanceDaily 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unit SSPET5 5.2. Servicing the conveyorMaintenance Maintenance InstallationRemoval SSPET5Assembly sealing ring SSPET5 5.2.2. Changing the sealing ring of the outlet flapMaintenance SM4-630SSPET5 5.2.3. Adjusting the flap switch MaintenanceSSPET5 5.3. Replacing carbon brushes at turbine MaintenanceSSPET5 SM4-630 SSPET5 Installation MaintenanceTechnical data 6. Technical dataOptional Features Basic VersionSSPET5 Dimension Sheet Technical dataSM4-630 This parts list is only for the use of trained personnel only 7. Parts listParts list SSPET5SSPET5 SSPET5 Parts listSM4-630 Parts list Order noDesignation SSPET5SSPET5 8. AccessoriesAccessories SM4-630